您好,我叫JiChi,来自中国,我是一名学生,已经玩了四年的DIY
New Members - please post your introductions here
Collapse
This is a sticky topic.
X
X
-
Hello
I am from Slovakia, guy which was born with electric cable in hand. After I learned walking, my first experiences made people around sometimes crazy, but don't worry, daddy was electrician, so his blood is running inside me, as we said - we are electric vaccinated from born
My computers experiences began with old microcomputer PP01, then I run over few platforms, until I ended on PC, where I stayed until now. My job is more focused on networking and servers, but my heart hobby stays untouched - electronic develop and repairs...
I had found few interesting topics here, so I made decision to try to register here and maybe sometime add my experiences, or share my request with people here...Comment
-
-
Hello everyone, this is my introduction. My name is Enrique and I'm from Mexico. I currently work in the IT field, so I work with computer equipment and often can't find anyone to repair some devices, so I decided to look for them here. Thanks in advance to everyone!
Comment
-
Electrical Engineer in training, looking to mod some of my devices and get ideas for future projects.Comment
-
-
-
Hi everyone,
I'm new to the Badcaps forum and excited to be here! I have a keen interest in electronics repair and I'm always looking to learn more. I've heard great things about this community and its wealth of knowledge. I'm looking forward to reading through the discussions, hopefully picking up some valuable tips, and eventually contributing where I can. Thanks for having me!
Comment
-
Hello everyone,
My name is Itallo, and I'm new to the world of electronics and circuit schematics. I'm just getting started in this field and eager to learn as much as I can. I joined this forum to connect with experienced members, share knowledge, and hopefully get some guidance as I begin exploring electronic equipment and how it all works.
Looking forward to learning from all of you!
Best regards,
ItalloComment
Related Topics
Collapse
-
by fredyjbiplease help friends thinkpad T470 board CT470 series NM-A931 error post "bottom cover tamper detection error"
I've already
flashed the bios clean me and updated from the Lenovo site, then removed the switch and immediately jumped the S3 from pins 1 to 4, 2 to 3 but the problem remained the same, thank you1 Photo -
by fredyjbiplease help friends, I have 3 T490 units with the same case, the USB type C is completely dead, showing 20v 0 amp, loss of voltage VINT20_IN resistance to ground is fine, thank you
I think the problem is that I lost the voltage at PQ0008 pon 1 -PWRSHUTDOWN which should have been high which was picked up by R9512 VCC3SW, thank you very much for your help
PF0002 20v
PQ0005
pin 5 20v
pin 1.2.3 19.8v
pin 4 19.8
resistance
source & drain 2,4 m
source & gate 100k
PQ0006
pin 1.2.3 19.8v
pin 4 19.8v... -
by fredyjbiplease help friends x1 yoga 7th no display beep melody thank you...
-
Channel: BIOS Requests ONLY!
-
-
by fredyjbiplease help friends clean me bios x1 yoga 7th no display melody beep, thank you
-
Channel: BIOS Requests ONLY!
-
-
by fredyjbiPlease help friends, thinkpad t480 nm-b501 is dead, help me fix it, thank you
usb meter 20v 0.00 amp, after I took the VSYS measurement the drop was only `9.2v which should have been 10.2v I measured from a normal matherboard machine, the VSYS path resistance to ground diode mode is 1900 thank you
LINK to Schematic -> https://www.badcaps.net/forum/troubl...b501-schematic - Loading...
- No more items.
Comment