VIZIO VA26LHDTV dirty cable end

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • reeferman
    New Member
    • Feb 2013
    • 9
    • USA
    #1

    VIZIO VA26LHDTV dirty cable end

    I'm having trouble with this 30 connector cable (20696 E221612-S, approx. 10 5/8” length).

    What I believe is adhesive (pix RH side) seeps out from the cable over a month or so killing the set. Maybe I'm wrong here.

    The adhesive is easily removed with MEK but it isn't a permanent fix. I treat the connector and cable end with Deoxit after cleaning.

    I haven't been able to locate any replacement cable on the net.

    Might anyone have a better cleaning idea or source for a replacement?

    TIA
    Phil
    Attached Files
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • SeaglassPearl
      Vizio E420VA 5v drops to 3v when power cable is connected
      by SeaglassPearl
      Folks, I have a Vizio flat screen that doesn't show any signs of life (and no orange vizio glow either).

      I tested the voltages from the power board (at the connector) and I can see the 5V supply drops to 3V after the power cable is connected to the main board (5V supply reads as 5V when cable is disconnected from main board). All other rails (12V and 24V) are reading fine.

      I looked for the usual bloated caps and saw none on either board and no other tell-tall signs (black marks, burned components, etc) on either side of both boards.

      Given the 5V rail...
      12-30-2022, 05:55 PM
    • howardc64
      A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
      by howardc64
      Problem

      This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
      08-04-2024, 10:36 PM
    • Grasshopper2Ant
      Vizio Flex Cable / Address Bar Repair
      by Grasshopper2Ant
      Vizio V755-G4 LED

      Doing backlight LED strips replace. All good till I decided to clean the screen with the address bar taped to screen.

      I accidentally dislodged the flex cable on the LED screen.

      I was choked after reading it was a pain to repair.

      Anyone out there have a solution for a layman without a bonding machine.

      I saw a square heating attachment to solder iron but have no idea where to get it.

      Any suggestions appreciated.

      I was so close to getting this damn thing assembled.
      08-11-2023, 10:15 PM
    • SS454
      vizio e650i-a2 backlight flashes then turns off
      by SS454
      vizio e650i-a2 (LWJAOZBP Serial) led backlight flashes then turns off, has video (via flashlight) and audio.

      panel: au optronics T650HVN05.4
      72 led total on 12 strips, 6 led per strip wired in three groups of 24 (led driver board has three anode and three cathode pins)
      link to datasheet: https://datasheetspdf.com/pdf-file/8.../T650HVN05.4/1

      Vizio 56.04219.641G (liteon PA-3231-01WN-LF) Power Supply Unit
      https://www.shopjimmy.com/vizio-56-0...-power-supply/

      Vizio 55.75J01.001G (91.75J10.004G) Main Board...
      08-20-2020, 03:57 PM
    • mrtek
      Vizio M65-C1
      by mrtek
      Hi.

      picked up another TV. This time is a Vizio M65-C1. TV does not turn on. I had repaired another 60 inch vizio , Bad main board.
      When power button is pressed, the Power led indicator on the bottom right, turns for a few seconds and then it fades away. No backlight or Vizio logo on screen. Removed back cover and repeated test.
      This is the TV This TV is a little different from the Samsung I have worked on. Power supply is on the Left side, Main Bd is on the right side, T-CON , not in the picture is on the bottom. I am assuming that the boards in the middle are the LED...
      07-14-2025, 07:28 PM
    • Loading...
    • No more items.
    Working...