HiSense 50CU6000 screen goes black after a few seconds

[Diah]

Re: HiSense 50CU6000 screen goes black after a few seconds

.

LOL..

its issue that t-con cant handle 2 channel signal... 99% firmware need to re flash.... and the reset 1% T-con HW fault

[Diah]

Re: HiSense 50CU6000 screen goes black after a few seconds

Man ...i asked you to feed signal.. we want to see when there are signal load on the t-con and panel.... also you need to do same way disconnect the other side

[nomoresonys]

Re: HiSense 50CU6000 screen goes black after a few seconds

The light comes on then goes out.

.

[MikeRWK]

Re: HiSense 50CU6000 screen goes black after a few seconds

by the way... what will happen if you feed it with signal and disconnect one ribbon at atime between panel & t-con did the issue remain

With the left tcon cable unplugged (right side of the screen when looking at it) the tv works and doesnt shut off.

[Diah]

Re: HiSense 50CU6000 screen goes black after a few seconds

I know what you're talking about but I have no experience with using terminal to do anything like this. What's a good linux distro I can boot from a usb drive to do this?

then download this firmware extract and flash it via usb formated fat32 .. press ok or power on the RC while you plug in the tv at wall socket

[MikeRWK]

Re: HiSense 50CU6000 screen goes black after a few seconds

you have on the main boards between the USB & HDMI 2 audio jack one of them are service jack .. can be used with any TTL serial with pc and terminal to read the log while the set booting as well the issue when it turn the screen off.

if you are familiar with terminal and Linux platform i think you know what i am talking on.

I know what you're talking about but I have no experience with using terminal to do anything like this. What's a good linux distro I can boot from a usb drive to do this?

[Diah]

Re: HiSense 50CU6000 screen goes black after a few seconds

Here's the main board do you need pics of the other boards?

you have on the main boards between the USB & HDMI 2 audio jack one of them are service jack .. can be used with any TTL serial with pc and terminal to read the log while the set booting as well the issue when it turn the screen off.

if you are familiar with terminal and Linux platform i think you know what i am talking on.

by the way... what will happen if you feed it with signal and disconnect one ribbon at atime between panel & t-con did the issue remain

[MikeRWK]

Re: HiSense 50CU6000 screen goes black after a few seconds

could you show us the whole back of the set boards??

the easy way to know why it goes black by trace the live log of the main boards via the service jack.

Here's the main board do you need pics of the other boards?

[Diah]

Re: HiSense 50CU6000 screen goes black after a few seconds

could you show us the whole back of the set boards??

the easy way to know why it goes black by trace the live log of the main boards via the service jack.

[MikeRWK]

Re: HiSense 50CU6000 screen goes black after a few seconds

Try unplug tv, unhook cable from mainboard to tcon, plug power cord back in, turn tv on, see if you have the red led lit up at the optical audio output on mainboard and if it stays on.

The light comes on then goes out.

[nomoresonys]

Re: HiSense 50CU6000 screen goes black after a few seconds

Try unplug tv, unhook cable from mainboard to tcon, plug power cord back in, turn tv on, see if you have the red led lit up at the optical audio output on mainboard and if it stays on.

[nomoresonys]

Re: HiSense 50CU6000 screen goes black after a few seconds

I wouldn't rule out the mainboard as the culprit.

[MikeRWK]

Re: HiSense 50CU6000 screen goes black after a few seconds

I've isolated the problem to the tcon, plugging it back in with the tv on it runs for the same 8-10 seconds then dies.

[MikeRWK]

Re: HiSense 50CU6000 screen goes black after a few seconds

Just wanted to add vgh starts at 21.9v then drops to 21.5v and then 0.3v when it happens, the 12v pin on tcon reads 11.9v.

[MikeRWK]

You can turn it on and it will boot up and after a few seconds the screen goes black but the backlight stays on and there's still sound. It will display picture briefly before it goes out.

Here it is coming on without a video source, there are some lines and tracers.
https://streamable.com/css91z

Here it is with a video source, no lines or anything.
https://streamable.com/y79wte

I'm also wondering if this transformer should have voltage going through that outer frame part in the picture, this was measured using hot ground.