Hi
Would anyone have the recovery files for this 17MB97 based main board please?
TIA
MC
Would anyone have the recovery files for this 17MB97 based main board please?
TIA
MC
-
-
Re: Panasonic TX48C300B - recovery F/W
try this to make the TV booting. -
Re: Panasonic TX48C300B - recovery F/W
If it does not work with the above software, also post the panel code.Comment
-
Re: Panasonic TX48C300B - recovery F/W
Hi
Thanks for the file - however still no joy - the TV just flashes the re power LED 10 times.
Main board Vestel is 17MB97 and the U81 on main board is a 25L1606E and the file implies 25L1605... - does that matter?
Panel label shows as - 10096599 - 23269708 96 48 27366448 DIJ.
Any help gratefully received.
TIA
MCComment
-
Re: Panasonic TX48C300B - recovery F/W
1. 25L1606=25L1605
2. Cod panel ex. VES480XXXXXXX (if the panel is Vestel)
3. The bin posted by Diah is for the programmer, not for the stickLast edited by yokoono; 07-25-2020, 08:24 AM.Comment
-
Re: Panasonic TX48C300B - recovery F/W
Hi
OK have removed 26L1606E and programmed chip with code (using CH341a and AsProgrammer s/w) - re-inserted into board but symptoms are the same - power LED pulses x 10 times at power on.
Attached is a pic of the labels on the board.
Anything else you can suggest/advise please?
Thanks again...
MCAttached Filesif you find these attachements useful please consider making a small donation to the site
Comment
-
-
Re: Panasonic TX48C300B - recovery F/W
Panel code is also required for correct software. It is written on a white label pasted on the back of the panel. At the Vestel panel it starts with VES ???????Comment
-
Re: Panasonic TX48C300B - recovery F/W
Hi Diah
Thanks for pointing me in the right direction - what I took as an error code of 10 flashes was in fact the normal startup of this set and of course there were no backlights.... - I checked around the MP3394 which seemed to be shutting down early as the VLED didn't really hit high enough to light the LED's. The OVP pin seemed to reach 1.25 volts so I checked the R's on this pin - 2 x 390K and 1 x 6K8 - I removed the 2 x 390K's off board to check and they seemed good so I soldered them back in - next time I checked the LED's lit and the set is running.
I haven't found a definite fault but suspect maybe some board leakage putting the IC into OVP prematurely. I have cleaned the board and will run the set.
Thanks for your pointer..... next time I'll state the fault up front
Cheers
MCComment
-
Re: Panasonic TX48C300B - recovery F/W
you welcomeComment
-
I suppose the real question is whether the existing pinouts from ether a 17IPS71 psu are cross compatible with a 17IPS12 psu? If they are then the exchange of the main boards should have no issues providing the screen is compatible with both main boards. Obviously you can change the screen configurations easily enough (providing you have the correct files) for the main board. Why may you ask would I do this? Well a lot of the smart features are no longer working on a Hitachi 48HBT62U main board I wish to give it a new lease of life!
Obviously the same LVDS connector for the screen connection... -
Hi everyone!
I happened several times, in the search for help from the web, to consult this very interesting forum.
So I decided to sign up and I intend to participate actively by making available my knowledge and experience on the subject, I'm a new user but at the same time I'm old in the sense that I have 4 decades of experience in repairing and designing electronics but above all I'm a great passionate about the subject.
Having said that I come to the gist of my post on the forum as the title suggests.
For my passion for technology I'm now collecting several... -
I've been working on this awful project with a Panasonic FZ-55, basically I'm trying to intercept the eDP signal from the main board, and replace it with my own eDP signal connected from an lcd driver. The problem is, for some reason the 30 pin ribbon pinout is really unusual and not playing nice with my LCD controller. Long story short, I managed to fuck up my board and pull off some pads on the eDP out port, I'm hoping to find either another eDP out source somewhere else on the laptop, or figure out this goddamn pin layout so I can just replace the whole native display complex with my controller... -
I have a Panasonic viera plasma Tx-P50G20B which has a faulty main board. The picture freezes after about 30s and appears to lose vertical hold before finally going black. The main board part number - TNPH0838 (1) A - is common to several Panasonic tvs across a number of ranges however there is a second part number (TXN/A1LTUB for the 50") which is unique to each model.
My question is, given that the TX-P50G20B 50" differs from the TX-P46G20B 46" only in the physical size of the screen, is it possible to use the main board from the TX-P46G20B in a 50"? The secondary... -
Hi and thanks in advance for any input you might provide!
I have a Sceptre U550CV-UMRD8POTV83BB 4K LED (this is a dumb tv) that I bought new in August 2021, so It's just completed 3 years.
Main power board model: TP.MS3683.PC821 T-Con board: N4TP546UHDPU2L_BO
Last Sunday I was watching a dvd and fell asleep for about half hour, when I awoke the tv screen was black and couldn't get the dvd menu to show, so I changed the input to antenna and had sound but no picture, turned it off. I then got online and found this great site! ....read many troubleshooting tips and this...
Comment