Bush LCD40883F

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • ronhayes
    TV Engineer
    • Mar 2014
    • 458
    • UK

    #1

    Bush LCD40883F

    Hi All
    Wonder if any one could help with some info on this set ?
    The original fault was no sound or intermittent sound. Now I know this was a faulty ic u168 audio amp chip as stated by Tom66.
    And as he said you need to remove this with a heat gun.
    Now I proceeded to do this with my work station heat gun and was being as careful as I could, but unfortunately a couple of the tracks got damaged !!
    Now I may be able to repair them but it will be very very difficult ?
    But before I attempted this I started a search on eBay to see if there was a replaceable board available ? And yes there was but they were a bit expensive at around £25 to £30 .
    But on a more intense search I found a identical board that looked exact in every detail but was from a different model TV. The board is from a Techwood 40940 FHDDIGITAL at a reasonable price.
    So I sent for it, when it arrived I compared it to the original board and it looks exact, So I went ahead and installed it.
    When I switched the TV on all worked ok good picture and sound.
    But when switched on the sound bar appears on screen and travels down to zero sound you can increase the sound on the remote by holding your finger on the v up button and pressing the ok button when it is at the desired volume.
    When you go into the menu and go onto picture and try to adjust any of the picture values :ie colour/brightness/contrast when you enter these it does the same the bar comes up and travels all the way to zero !!
    The set works ok nice picture and sound.
    I can tune in Freeview channels although only using a portable digital Arial that seems limited and have also tried the hdmi connections using a firestick and this works fine.
    What I think is my problem is maybe a software issue or would I have to set anything in the service mode.
    If any one could point me in the right direction to sort out the menu and volume issues it would be most appreciated.
  • dskall
    Badcaps Legend
    • Oct 2016
    • 2905
    • usa

    #2
    Re: Bush LCD40883F

    Duplicate post. See other post.
    I assume no responsibility for any stupid suggestions I might post.

    Comment

    Related Topics

    Collapse

    • TR103
      Samsung TV model UE50TU: rebooting, backlight, sound, but no picture
      by TR103
      Hi, I have a Samsung UE50TU with:
      - sound and backlight, but no picture
      - when it arrived, it had a picture for a few seconds
      - it keeps rebooting
      - without ribbon cable between the two panel boards, it does not reboot but I have no picture
      - without cable between mainboard and lcd panel, it does not reboot (but obviously i have no picture)
      - when i try a tape fix, its keeps rebooting, unless I tape off pin 1 (the innermost pin). In that case it does not reboot but I have no picture.

      - without cable between mainboard and lcd panel and with a jumpered...
      01-22-2025, 04:12 PM
    • Mgiffune
      Samsung UN60EH6000F Black Screen, Backlight and Sound Good. Power Cycle Returns Picture
      by Mgiffune
      I have a 60 inch Samsung UN60EH6000F flatscreen TV. The screen went black a few months ago Sound is good, backlight is good, no menu. I replaced the TCon board with a used board purchased from Ebay. It worked fine for a 3-4 months, then the screen started ‘fading' back. Once again, sound is good, backlight is good, no menu. However, this time the picture looks fine for about 10-15 minutes, then fades back. If I power cycle the TV, the display reappears, for another 10-15 minutes, then fades black again. Repeatable ever time.

      I ordered a supposedly ‘new' Tcon board this time, and
      ...
      06-09-2024, 10:28 AM
    • Ierwin
      Samsung UE60KU6079 backlight okay mainboard responsive, no picture, no sound
      by Ierwin
      Hello everyone,
      Ive got a UE60KU6079 on the workbench that is giving me some headaches trying to troubleshoot.
      The previous owner stated that there had been white dots on the screen which from the description sounded like some lenses fell of the backlight LEDs.
      He had opened the TV from the back, trying to get to the backlight, supposedly gave up, reassebled everything and gave the TV to me.
      I expected the worst like ripped COF cables or a cracked panel but could not find anything like that yet.
      Anyway I still fully expect that there has been something seriously damaged...
      05-13-2025, 03:31 PM
    • jchang
      Samsung UN70NU6900F no picture and no sound
      by jchang
      Hi all

      I was just given a Samsung TV with the issue. I read various threads and videos and attempted the ribbon tape method to gain an image, but no luck.



      Symptom:
      No picture no sound.
      When I plug in the power cord, Backlight LED turns on for a half second and then turns off. The red LED next to the power button located center bottom flashes 2 or 3 times. When the power button is pressed after, it does the same thing.
      No sound at all.



      What I tried:
      1. I tried unplugging the left or right ribbon...
      01-09-2023, 06:28 PM
    • ChaosLegionnaire
      what i went through dealing with my mobo with dead onboard sound!
      by ChaosLegionnaire
      so i took out one of my spare gigabyte ep35-ds3r mobos from storage for use to do some cpu, ram and video card testing of stuff i bought from ebay and got for free from momaka. he bought 50 e8400 cpus for cheap from ebay some years ago and i decided to help him relieve him of some of his supply since he had waaaay too many!! what did we say about hoarding too much stuff and depriving others of them?! *cough* socialism *cough* lol!

      i had to blow some dust off the board and heatsinks with the datavac as i didnt clean it up before putting it in storage. after finishing...
      09-13-2022, 09:02 AM
    • Loading...
    • No more items.
    Working...