Panasonic DMP-BD87- Unit Stuck On 'Hello'

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • TechGeek
    Computer Geek
    • Jan 2015
    • 2254
    • USA
    #1

    Panasonic DMP-BD87- Unit Stuck On 'Hello'

    Hello all. I got this BluRay player some time ago and it has a problem...

    Upon plugging it in, it does nothing. Pressing 'Power' switches it on. Upon powerup, it says 'Hello', does not output a picture, and the disc tray ejects and returns once. After that, I have to unplug it and plug it back in again to get a disc back. Pressing 'Power' once it's on will NOT power down the unit.

    What is going on here? Thanks.
    Don't buy those $10 PSU "specials". They fail, and they have taken whole computers with them.

    My computer doubles as a space heater.

    Permanently Retired Systems:
    RIP Advantech UNO-3072LA (2008-2021) - Decommissioned and taken out of service permanently due to lack of software support for it. Not very likely to ever be recommissioned again.
    Asus Q550LF (Old main laptop, 2014-2022) - Decommissioned and stripped due to a myriad of problems, the main battery bloating being the final nail in the coffin.


    Kooky and Kool Systems
    - 1996 Power Macintosh 7200/120 + PC Compatibility Card - Under Restoration
    - 1993 Gateway 2000 80486DX/50 - Fully Operational/WIP
    - 2004 Athlon 64 Retro Gaming System - Indefinitely Parked
    - Main Workstation - Fully operational!

    sigpic
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • Junior††
      PS5 Disc Not Supported/ Disc Not Recognized Board Num: EDM-020
      by Junior††


      Good Afternoon fellas,

      Issue:
      Disc is showing as not supported when a disc is put in.

      Here's what I've done, you can skip this if you just wanna know the question:
      - replaced with a disc drive from a donor ps5 (honestly questionable if this is known to work)
      - reflowed the disc drive connector
      -reflowed the chip in question (shown on image)
      - I will say this console was very dusty so it's conceivable that it got so hot that it made the chip joints cold and potentially other things on the board

      Question:
      I...
      02-19-2025, 12:48 PM
    • Andre Gilbert
      Panasonic TC-P55ST50 8 blinks then no blinks
      by Andre Gilbert
      Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing here🤔?
      Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting 😂.

      TV Model: Panasonic TC-P55ST50
      ...
      1 Photo
      11-20-2024, 08:52 PM
    • Ancient1
      I'm stuck . Panasonic TH-L32U20M panel's boards issue
      by Ancient1
      Hi

      The TV seem to start ( blinking green) but goes into blinking red. No display and or backlight. Full view photo.

      Actions :

      1. Disconnected Panel's Right, 2nd, board : TV comes ON (steady green , no blinking red )
      1a. You can see in two photos the B/W screen , fading blue "HDMI12" , and the wierd sides of the image, like an old CRT.
      Obviously the fault is from or on the Right, secondary board

      2. I taped the Flex tracks, ~2 tracks at a time- see Photo. The issue seems to be on the V lines (Assuming Data...
      09-03-2023, 03:51 AM
    • ngml
      Repair of an LG split AC system indoor unit PCB
      by ngml
      I am trying to repair an LG split AC indoor unit, which does not start and gives a CH05 error code.
      This indicates an error in the communication between the outdoor and the indoor unit.
      The outdoor unit is fine, so the problem is the indoor PCB.
      The indoor unit is an LG PC09SQ NSJ (3SNM09JA2FA), and the PCB has the following type number: EAX35907219-1.2 (see photo1)
      I changed optocouplers ICO1X & ICO2X and the NPN transistor S9013 which drives optocoupler ICO2X (see photo2), but this did not remedy the fault.

      Does anybody have the schematics of this board,...
      2 Photos
      02-01-2025, 12:55 PM
    • stormanimal83
      Gigabyte B450 Aorus Pro stuck at VGA LED, burning hot LED Controller MCU 1 under PCI slot...
      by stormanimal83
      Hey....

      Board as written in description was stuck at VGA LED. common Problem wit these type of bords.... tried all the "standard stuff" like resettin... reseatin.... found out the LED Controller MCU1 = IT8295FN-56A geting burning hot under the last PCI Slot.. now i desoldered it cause there were only 18 ohms at the caps arround.... another aorus x470 in working condition with similar part and nearly same layout had arround 280 ohms...

      my question is: why doesnt the board start know without this chip.... worked myself through the boardview but i can´t understand...
      01-18-2024, 02:15 PM
    • Loading...
    • No more items.
    Working...