LG 60PA6500 - Relay Clicking

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • somosdel
    New Member
    • Sep 2016
    • 2
    • USA
    #1

    LG 60PA6500 - Relay Clicking

    Hi All,

    First time poster and long time lurker. I figured I would post my problem and I know that the people on this board would have the "know-how" to help me.

    I have an LG 60PA6500 TV. Few weeks back the dreaded "Click" relay on/off issue began. When the power is plugged in all that is heard is a click then another click. TV will not turn on.

    I did my research and checked all the capacitors. None looked bad and no signs of any damage anywhere. I replaced the c802 capacitor which is usually the culprit. After replacing that capacitor, the tv is still doing the same thing. That didn't solve the problem.

    Am I looking at replacing a power supply board? Wanted to pick your brains before I waste more money and get the wrong part.

    Any help is greatly appreciated and thank you in advance!

    Sincerely,
    Kenneth
    Tags: None
    • tvtimmy
      Badcaps Legend
      • Mar 2015
      • 1160
      • usa
      #2
      Re: LG 60PA6500 - Relay Clicking

      Unplug the zsus board from the power supply. It will prob. stay on. 6 blown 30f126 fets and 1 diode(marked 2001 or something) for sure.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • beetle1303
          Carver CM-1090 - Power relay clicking on & off, then fuse blown after 20-30 seconds of power cycling.
          by beetle1303
          I gotten a Carver CM-1090 amplifier from a friend who has kept it in storage for decades. Opened it up, thick layer of dust cumulated everywhere. Vacuumed it semi-cleaned, and blown off as much as possible the remaining dust. This is a 220V version.

          On initial powered up with nothing connected - it works with all the lights and button indicator lit up as pressed, etc. I then powered off, connected a CD player into the CD RCA input and powered it on. It seemed to work for a short while and when I turned the volume up and down to see the the VUs works, the power started to clicked off...
          3 Photos
          01-13-2025, 08:49 PM
        • CoinCoin88
          Garage door RX unit (Cardin S38C) does not short relay to send opening signal
          by CoinCoin88
          Hello everyone,

          I'm turning to the Badcaps community to help me troubleshoot the radio Rx card from my (old) garage door opener. While I could just ditch that card and replace the whole system, I first would like to understand "why" it suddenly stopped working, because that's just how I am wired...!

          Some basics: the receiver works on a 30.875 Mhz frequency. Yes, I'm aware this is not in use anymore in a looot of places. It does not use any rolling code, it's just a regular dip-switch code that you have to set up on both the receiver and transmitter. The receiver...
          09-15-2025, 03:36 AM
        • DodgyTech
          60" LG 60PB690V relay clicking issue
          by DodgyTech
          Hi everyone,

          I require some help with my TV. The TV standby light blicks on and off with a clicking sound (relay?) from the back. After I opened up the TV, I set about troubleshooting by unplugging the boards to try and isolate the problem. My troubleshooting suggests that the logic board is causing the issue, but it could entirely be the YSUS board which is only activated once the logic board is connected.

          I have recorded a video which I thought would be an easier way to explain the problem and show the boards at the same time.

          I would like to try and identify...
          07-07-2023, 10:30 AM
        • GraphicMan
          Pioneer amplifier A-205 Relay not clicking after a mistake i made
          by GraphicMan
          Hello guys
          Because the unit is old (but only occasionally used) the loudness button causes some noise due to bad contact,
          sprays did not work, so i decided to solder the pins that it connects on the pcb at the on (loudness on) position
          i did that and it worked fine, i know from the bottom of my heart that the switch connects 2 pins and also d/c other 2 pins
          on every position it have (6 pin switch), so i was curious what would happen if i clicked the switch off while the pins are soldered at on (so basiclly on and off at the same time), when i did so the sound is gone, nothing...
          05-05-2024, 06:20 AM
        • Sisko
          Onkyo-593 No power and now clicking sound
          by Sisko
          Hi all!!

          Ok just got a Onkyo SKW-593 sub woofer that has no power person told me that it smoked and that his GF let the volume full when she powered off the amp and when he came to turn it on the sub played but then suddenly smoke was coming out, didn't say from where. So opened it up and saw a resistor made of metal (pic) but can't see any writing on metal par so what ever was written on it was burnt. So I'm kinda stuck here with this. I did ask for a repair or schematics in the other group section and waiting for this but I hope someone here might lend me a hand to try and identify...
          Schem
          4 Photos
          10-03-2025, 02:18 PM
        • Loading...
        • No more items.
        Working...