hisense 55k610gwn no power no standby

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • hmendez86
    Badcaps Veteran
    • Jun 2015
    • 344
    • united states
    #21
    Re: hisense 55k610gwn no power no standby

    Well I just plug the power alone to ac cord with out main and led connection.....when I check for 5v stanby there's none only the 16v and 12v....I have on the board label pWm which is 4.44v and sw 4.44v but no 5v on standby.........when I connect the main it's a buzzing noise from power and goes on, but on the Stanby I get 24.v......need to get new meter numbers in this one are death..

      Comment

      • budm
        Badcaps Legend
        • Feb 2010
        • 40746
        • USA
        #22
        Re: hisense 55k610gwn no power no standby

        The 12V and the 16V are the Standby Voltage on this power supply board, as indicated in my post #6.
        STB pin is the same as PS-ON pin on this power supply board as you can see from the bottom side of the board.
        https://www.badcaps.net/forum/attach...1&d=1472187103

        Where is the 5V pin on this board? I do not see one.
        https://www.badcaps.net/forum/attach...3&d=1472170236

        STB = PS-ON
        SW = BL-ON
        PWM = PWM dimming
        Last edited by budm; 08-27-2016, 07:04 PM.
        Never stop learning
        Basic LCD TV and Monitor troubleshooting guides.
        http://www.badcaps.net/forum/showthr...956#post305956

        Voltage Regulator (LDO) testing:
        http://www.badcaps.net/forum/showthr...999#post300999

        Inverter testing using old CFL:
        http://www.badcaps.net/forum/showthr...er+testing+cfl

        Tear down pictures : Hit the ">" Show Albums and stories" on the left side
        http://s807.photobucket.com/user/budm/library/

        TV Factory reset codes listing:
        http://www.badcaps.net/forum/showthread.php?t=24809

          Comment

          • shaundh
            Member
            • Aug 2016
            • 17
            • United States
            #23
            Re: hisense 55k610gwn no power no standby

            Man! I'm working on this same board. Got the exact TV today. It burned some components though. Not to thread jack, but I will subscribe to this thread.

              Comment

              Previous 1 2 template Next

              Related Topics

              Collapse
              • LemoneyF
                Hisense 50r6- no standby, no power, bad main board?
                by LemoneyF
                Hi all

                I have a Hisense 50r6 that quit suddenly, immediately after turning it on. It no longer shows red a standby light and will not turn on. Completely dead.

                I have tested the power supply and found the following:

                363V and 373V across the input caps

                bri- 0V
                ana- 0V
                vamp-17.03V
                vamp-17.03V
                stb- 0V
                12V- 9.3V
                12V- 9.3V

                To the extent of my knowledge (...not far!) these numbers are normal for a Hisense power supply in a standby state, though I would like some confirmation that 9v...
                10-12-2022, 07:44 AM
              • toty79
                Hisense LTDN50K220WSEU stuck in standby
                by toty79
                Hello to all friends of the forum and well found, here I am asking for your help and sorry for my translated English.



                As per Hisense tv title LTDN50K220WSEU stuck in standby
                PSU rsag.820.5687 HLL 4855WF
                Main rsag 7.820.5842
                I enclose the psu diagram, after the first routine checks I find myself with a regular standby voltage of 3.3v blue light on steady when the power button is pressed nothing happens, psu disassembled and bench checked ... forced ignition by sending a signal 3 , 3v on the SW and PWM2 pins the psu turns on and delivers all the voltages...
                05-01-2022, 04:39 PM
              • scottsman76
                Hisense 50B7100UW no standby but all votages seem to be there
                by scottsman76
                Hi All

                I have this tv and if I measure the various coils i get 3.3v, 5v, 12v and a 1v.
                But i have no Standby Light and no reaction from the switch.

                If I measure the the pins going to the rx and switch I Get 5v and a few other pins give 3.3v

                Where do I start looking with something like this, could it be the processor. I do feel that its slightly warm. not hot at all.

                Thanks
                Gav...
                07-04-2023, 04:38 AM
              • tvguy12012012120
                Zombie Samsung UN55NU6900F dead / no standby voltage - randomly came to life after hours of troubleshooting then died
                by tvguy12012012120
                This is my first attempt at troubleshooting a board like this, I know I could just buy a new board but I'm curious to figure out how this works. I've been testing different components in the evenings this week and I think the problem is with the IC failing to start up for some reason. When the board is plugged in there is no standby voltage.

                Then today it randomly sprung to life like a zombie but shortly died thereafter. I have no idea why it would have done that and its the first time I've seen it running. I discharged capacitors on the board last night, then it was sitting today....
                02-07-2025, 05:13 PM
              • EUWest
                Hisense rsag7.820.5687 no power no standby light
                by EUWest
                Hi!

                I have a power supply and on the TV no standby and no power. Have already installed a replacement power supply but the same problem.

                When I test both power supplies the main capacitors while plugged in, I get 0v.

                What could be the reason for this?...
                04-14-2023, 08:59 AM
              • Loading...
              • No more items.
              Working...