Just got this tonight. Panel hours says 00513h38m. Does this mean its been on for 513 hours total as it seems in plausible here is a photo of the service menu. Is it possible someone has reset this. Cheers.
Attached Files
-
-
Re: Pioneer pdp-427xd panel hours?
First off can I ask how you get into the SM ? Also yes 513 hours is very low tbh basically new
Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !
https://www.facebook.com/Telford-Tel...7894576335359/ -
Re: Pioneer pdp-427xd panel hours?
Turn tv on to analogue tv channel by pressing number button ie number 2. Then press standby. Then quickly before it clicks press info. Then after it clicks press left up left right standby. Worked first time for meComment
-
Re: Pioneer pdp-427xd panel hours?
Ok cheers, also I dont think there is a way to rest it. Does it look physically like its had more use age. Maybe take the back off ?Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !
https://www.facebook.com/Telford-Tel...7894576335359/Comment
-
Re: Pioneer pdp-427xd panel hours?
Well the p count that i presume is power on times is over 5000. Is p count power on times? Its a shame really. Paid £10.50 for it cause they thought the hdmi ports were broken but they were just turned off in the menu.
They didnt mention the light 4 inch scratch right down the center of the screen. Ill see if i can polish it out or something but if not ill probably end up stripping it.Comment
-
Re: Pioneer pdp-427xd panel hours?
Narr dont strip it, these are good Tv's tbh. Also you might be correct as well.Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !
https://www.facebook.com/Telford-Tel...7894576335359/Comment
-
Re: Pioneer pdp-427xd panel hours?
Also I want to say thanks for that info, helped me finally get into the SM on my 508XD lol fucking hell also this has less than 2000 hours on it !Attached FilesPlease Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !
https://www.facebook.com/Telford-Tel...7894576335359/Comment
-
-
Issue: Panel is partially dark or dimmed, left side is okay (see photos attached).
Trial: Replaced three visibly bad capacitors on the power supply board (see photos).
First result: Monitor worked for two hours only. Two capacitors bulged again.
Diagnosis: After replacing those capacitors the monitor was connected via HDMI cable to a laptop. Laptop was connected to power supply and charging. Power cable was removed from the laptop end and put back. Maybe this was a coincidence but since unplugging the power cable it was noted that the panel had darkened... -
49UJ6500 LCD panel has a lighter band on top when first powered on. Goes away (or gets much fainter) after TV on for a few min. After powered off for awhile and power back on, same band appears. If powered on immediately after powering off, no or much fainter band. Running the latest firmware.
Disassembled the TV and lifted the LCD panel during testing. Band is on the LCD panel (can see the band on the panel as I lift it slightly) Backlight is perfectly even at the top edge. Double checked LCD panel alignment in the frame and is perfect but since band moved with the panel, its on... -
TV flashes backlight then reboots over and over. no image. Client said it used to have image for a bit before rebooting. Got worse over time.
tcon is built into mainboard.
Only one cable goes to panel boards.
there is a cable from one panel board to the other that links them.
cost cutting measure that results in us having harder time to diagnose.
removing the link to the second panel board allows TV to stay on with stable backlight but no image.
used cut off tape method to mask 1 maybe 2 pins on the side of the cable that goes to that second panel board.... -
I had a the above tv qn55q60r that had a bad panel but everything else good. I had another panel here from un55nu6900 with bad leds and melted diffusers.
I put the nu6900 panel in and powered it up and it does work but there are lines vertical lines.
I was trying to change the panel type in the service menu but don’t see my exact panel. Anyway to fix this or someone have similar experience.
the clear picture is the panel type from the service menus on the nu6900. The other 1 is the panel type that was set for the q60r with the bad panel....01-13-2024, 01:57 PM -
I have a TCL 55P6US with sound and backlight but no picture. This model does not have a T-CON board, and the right (rear perspective) panel board is fed from the left panel board. I have not been able to induce any change by disconnecting the secondary panel board or the tape cut-off method on the primary board.
There are a bunch of voltages missing on the panel boards. I can't find any shorted caps of the panel boards, and all of the missing voltage rails read in the kiloohms, which leads me to suspect the issue may lie on the circuit board, rather than a short in the panel.
...
Comment