China power supply schematics (VESTEL)

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
Previous template Next

Related Topics

Collapse
  • Tynan Dill
    Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
    by Tynan Dill
    I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

    Upon bringing it home and plugging it up, it showed a standby light.

    I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

    The screen seems to blackout and stay black, but with a flashlight I can see the display.

    With my Playstation 4 connected via HDMI, and running a game I can hear sound.

    Assuming...
    ORIGINAL POWER SUPPLY BOARD
    7 Photos
    11-22-2024, 01:46 PM
  • sam_sam_sam
    Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
    by sam_sam_sam
    I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

    One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
    03-31-2024, 02:12 PM
  • sam_sam_sam
    Modification to a ZD-987 desoldering/soldering station using a external switching power supply
    by sam_sam_sam
    I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

    I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
    07-01-2024, 06:34 AM
  • JimBanville
    Definitive technology SC 2000 subwoofer amp's power supply clicking and popping
    by JimBanville
    The sub developed a constant popping every couple seconds from woofer and power LED flickering with nothing but wall AC connected. Connecting an audio cable didn't change anything. It doesn't play but a second or two of audio in between the pops.
    Opened it up and discovered the power supply is making a faint clicking or ticking sound.
    I measured the amp's output to the woofer and it pulses up to 50mv DC to be driver. The pulses coincide with the power supply ticking/clicking.
    I measured the power supply output going to the amp board and it too has this pulsing. Voltage cycles...
    09-13-2023, 07:21 AM
  • Andreas_de
    Power supply Manson NTP-5561 (5661) LCD controller dead - PIC18F87K90 HEX dump required
    by Andreas_de
    Hello!

    i got a damaged Manson NTP-5561 (60V, 1,6A DC output) and and the main issue is that the controler IC for the LCD display has a short. The controler IC PIC18F87K90 is mounted on the back of the back of the LCD. Vss-Vdd = 3 Ohm. The 5V and 3,3V power line was killed as well, but that is not a problem. A new LDO 3,3V and 5V 7805 is already ordered.
    Replacing the PIC18F87K90 is necessary but that makes no sense without having the HEX dump of the new controler.

    Does anybody have such a power supply and could do a HEX dump of the Flash and EEPROM memory?
    ...
    2 Photos
    04-12-2025, 10:38 AM
  • Loading...
  • No more items.
Working...