LG 32LV3400zg starts fews minutes later

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • fpsousa
    Member
    • Dec 2015
    • 29
    • Portugal

    #1

    LG 32LV3400zg starts fews minutes later

    Hi,
    I have a TV led LG that sometimes, starts and all is running ok and sometimes, don´t start immediately; sometimes (not always the same), could be 5 sec or 10 minutes later, it starts.
    Measures: PSU - 3.5 V ST-BY is always ok but misses RL_ON from the uP. When it turns on, the 12V a 24V are ok too, so the PSU seems to be ok.
    On main board I've checked that 24 Mhz crystal is ok, and uP generate POWER ON/OFF but RL_ON don´t.
    On panel Led indicator is blue (on).
    If the TV remain connect with mains 220V and Red led is light, the Tv starts but if disconnected from mains the malfunction appears.
    I have schematic.
    Attached Files

Related Topics

Collapse

  • chaos-theory
    Asrock z97x starts then shuts off after 4 seconds, sometimes more, no post
    by chaos-theory
    I have a really weird problem, this motherboard was working normally, someday it just started and all fans were running but didn't want to post, tried resetting bios, checking CPU and it was getting warm tried external gpu, flashed bios with programmer, but same problem.
    Next day after several attempts the board goes into protection mode, no more staying on, I turn on the PSU fans starts directly turning, it used to not start until I press the pwr button, now it starts directly and fans spins, and shuts off after 3 seconds sometimes less, then won't start again unless I unplug the PSU and...
    03-14-2025, 05:37 PM
  • arabex21
    Asus Prime B450M-A starts only when 12v 8pin cpu plug disconnected
    by arabex21
    Hello everyone. I have been reading this forum for a long time - I really appreciate the amount of very interesting materials and information in the field of electronics.

    I have a problem with this configuration:
    ASUS PRIME B450M-A
    RYZEN 1300X (I replaced it with ATHLON 200GE - the same behavior, the processors are functional, tested on another board)

    When the entire set is installed (CPU, RAM, ATX connector and 12V 8 pin CPU plug), the board starts up for a while (about 1-2 seconds), the CPU fan starts and the board turns off immediately. When I disconnect...
    09-19-2024, 03:05 AM
  • master3112
    Lenovo E15 Gen.3 NM-D481 No starting and charging via USB-C, The device starts only via the battery.
    by master3112
    I have a Lenovo E15 Gen.3, motherboard NM-D481 with a defective USB-C port. The device starts with battery. When connected to the USB-C power supply, it does not start or charge. 20V is present at the input of the UT5 (High voltage USB PD power switch), 0V at the output
    UT5 pin 3 (SNK_PS_EN) =0V
    RPT3 Pin1+2 LDO 3V3 present
    I suspect that the UT2 USB-C power controller is defective because the UT5 is only controlled by the UT2. However, the UT2 supplies on pin 33 (+LDO_3V3) which makes me wonder if it is defective after all. Unfortunately I don't have it here to test it.
    ...
    08-02-2025, 12:30 PM
  • Shobos
    Dell E6420 XFR Rugged starts to boot but after 3 secs shuts down.
    by Shobos
    Hi, I bought 6420 XFR that tries to boot but shuts down after about 3 seconds, CPU gets warm, fan starts.
    So far I have tested all rails wich are good, BIOS flashed with CH341, 3.3,5, main rail present. multiple ram sticks tested. Sometimes it might stay on for longer like 4-5 seconds but not always, theres no picture whatsoever. Also on some rare occasions the caps lock flashes 1 time by itself.
    NOTE: I am using bench power supply not dell charger with ID pin and NO battery present, kinda doubtful this would cause this issue.
    Any help is welcome. Thanks !
    07-29-2025, 03:53 PM
  • JohnML1975
    LG 49UK7550PTA - after couple of hours screen starts to blink
    by JohnML1975
    Hello Forum team

    Have this TV; searched for the model and could not anything so thought I would share in here

    Had an issue, some years ago, and looks like some placed sticky tape over some of the lines on the FFC cables between the T con and the mainboard
    Anyway, the owner, who gave me the TV, says it starts to blink after a few hours

    So I removed the covers, and could not see anything visibly
    Removed the power supply and thought some of the solder joints, on the hot side, were not the best. I thought some looked like they were cracked.
    ...
    07-25-2025, 10:48 PM
  • Loading...
  • No more items.
Working...