Bush pdp42hd3 aka ps42c450

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • wills123
    Senior Member
    • Jan 2014
    • 72
    • england
    #1

    Bush pdp42hd3 aka ps42c450

    I have this set in at the moment, lowest buffer ic s/c, two outer fets on x main sc, ysus tests ok,
    If I replace the x main fets and remove the sc buffer ic, will the set fire up with just a blank row? Do other damage? I don't want to purchase a y main as well if not needed but research suggests peopl change all 3 boards,
    Thanks for any help/ thoughts
    Tags: None
    • finntricky
      Badcaps Veteran
      • Jan 2014
      • 449
      • uk
      #2
      Re: Bush pdp42hd3 aka ps42c450

      I got hold of one of these a few weeks ago, turned out to be y sus, has luck would have it I had a 42PS450 with a broken screen sitting in the shed, result,
      But I must say what a heep of shit it is, but only paid£10 for it, so can't complain.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • howardc64
          TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
          by howardc64
          All left and right refers to looking from rear of TV (or looking from front with TV upside down)
          • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
          • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
          ...
          07-24-2025, 05:17 PM
        • howardc64
          A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
          by howardc64
          Problem

          This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
          08-04-2024, 10:36 PM
        • cheeky2
          Is it possible to upgrade from a Vestel 17MB97 main board to a 17MB110 Main board?
          by cheeky2
          I suppose the real question is whether the existing pinouts from ether a 17IPS71 psu are cross compatible with a 17IPS12 psu? If they are then the exchange of the main boards should have no issues providing the screen is compatible with both main boards. Obviously you can change the screen configurations easily enough (providing you have the correct files) for the main board. Why may you ask would I do this? Well a lot of the smart features are no longer working on a Hitachi 48HBT62U main board I wish to give it a new lease of life!
          Obviously the same LVDS connector for the screen connection...
          05-25-2024, 03:27 AM
        • Dani_2024
          Sceptre U550CV-UMR 4K LED, Bad Caps on Main Power Board?
          by Dani_2024
          Hi and thanks in advance for any input you might provide!
          I have a Sceptre U550CV-UMRD8POTV83BB 4K LED (this is a dumb tv) that I bought new in August 2021, so It's just completed 3 years.
          Main power board model: TP.MS3683.PC821 T-Con board: N4TP546UHDPU2L_BO

          Last Sunday I was watching a dvd and fell asleep for about half hour, when I awoke the tv screen was black and couldn't get the dvd menu to show, so I changed the input to antenna and had sound but no picture, turned it off. I then got online and found this great site! ....read many troubleshooting tips and this...
          5 Photos
          10-28-2024, 05:06 PM
        • howardc64
          Samsung QN75Q6FNA backlight no display, red LED blink 2x, fault in panel
          by howardc64
          • Prior owner tried a replacement main board. No difference.
          • Samsung 2x red blinking standby LED = panel fault
          • Jumpered FB_TRDY_1 (pin 1 CN1300 left. main tcon->left side buffer boards) and FB_TRDY_3 (pin 95 CN1301 right. main tcon->right side buffer boards) This allows testing individual T-Con (on main board) connection to panel on this Samsung. Found fault on left side (viewing from rear of TV)
          • Each side has 2 buffer boards, disconnected left side flex between 2 buffer boards. Fault is on the left most board.
          • Tape masking eventually isolated to CN1300 pin 15 (CKV4_GOA) Display
          ...
          07-19-2025, 10:54 PM
        • Loading...
        • No more items.
        Working...