Re: 55 inch Panasonic fit in my trunk!
50 lg plasma in a y reg vectra, it fit with about 1mm either side with the rear seats down, thought I was gonna have to borrow my brothers transit lolz
wills123
Senior Member
Last Activity: 03-19-2018, 02:13 PM
Joined: 01-21-2014
Location: norfolk
-
Re: diagnose samsung plasma ps50c550....
At razor, yes xsus has a fault, test the y buffer board an u may find that has short too, on the smaller sets its the two outer fets on xsus that short, u may be able to replace just those but be warned if buffer has a fault or the y sums it will short again. Most people reccomended changing all 3 boards on the ps42c series. Just be sure to check each replacement board as there is a lot of faulty ones out there. I have two ps42c that need buffer boards that I have yet to locate good ones, had 4 sent to me faulty lolLeave a comment:
-
Re: diagnose samsung plasma ps50c550....
Test the boards for short circuit between vs,va and ground you may find its shorted some fets like the smaller ones doLeave a comment:
-
Re: Is it possible to fix Plasma panel?
Would expect a shorted chip on y buffer, causing the y and x to blow again, y buffer boards should always be tested before replacing other boards on plasma TV! Tom666 has a good video showing how test buffer boardsLeave a comment:
-
Re: LCD42761F acoustic solutions tv
That's a vestel based unit, I had one in a technical model with main board fault that wasn't switching the psu on, never did narrow down the exact fault but replacement main cured it, be sure to check all psu voltages are coming up first though, there are schematics available onlineLeave a comment:
-
Re: Ssi_400_14a01
Ah wish I caught this sooner I. Have one those boards that wudnt switch backlight u could of had it for the parts for post cost, I resolved mine by switching the good lcd. From that one into a toshiba (vestel ) of same size that had bad panel lolLeave a comment:
-
Re: Wharfdale no sound through HDMI
Have u ruled out the obvious and tried another hdmi cable and another input device?Leave a comment:
-
Re: LG42PT350R clicking and doesn't turn on
You connect each one in turn and the voltages drop? Or all of them?, try to connect all but the x an y then see if the voltages still there, test for short circuit on x an y between vs and ground for a starterLeave a comment:
-
Re: LE37M88BD Possibly Bad Lcd ?
Nice, worth a punt at that for sure
but I am a hoarder lol, I have a shed full of sets cheap/free that are for spares, mostly old obsolete stuff but handy sometimes 
Leave a comment:
-
Re: LE37M88BD Possibly Bad Lcd ?
If you sell parts it's worth a punt, if you don't I wudnt gamble on it, they suffer tab bond problems terriblyLeave a comment:
-
Re: 17MB35-4 3.3V Shorted Help ?
Nice one hope you get it replaced easy enough
Leave a comment:
-
Re: TNPH0784 14 Blinks SOS Repair
If u ever decide to get into bga equipment give me a shout I have a reasonable amount of experience from console repairs an the few TVs I've done so might be able to help
Leave a comment:
-
Re: 17MB35-4 3.3V Shorted Help ?
Not sure if it helps but I used to fault find xbox360 shorts by jumping a pc psu always on then jumper wire affected rail and either smoke or very hot component usually made it fast to find problem
Leave a comment:
-
Re: 17pw26-3 Psu Unstable Output Any Ideas ?
I'm sure you have plenty of spares from these wonderful vestel TVs, I have cut the cables from a couple and soldered auto bulbs on the end to quickly plug in and test makes life a bit easier since most of them use the same plug types
Leave a comment:
-
Bush pdp42hd3 aka ps42c450
I have this set in at the moment, lowest buffer ic s/c, two outer fets on x main sc, ysus tests ok,
If I replace the x main fets and remove the sc buffer ic, will the set fire up with just a blank row? Do other damage? I don't want to purchase a y main as well if not needed but research suggests peopl change all 3 boards,
Thanks for any help/ thoughts -
Re: Just wondering can one of you guys point me in the right direction please LG 42pc
reecy has given you the best advice, using a multi meter test the voltages, being very careful as there are some high voltages in plasma tv that can stop your heart !!!!!!!!!!
All the voltages on theese tvs are marked on each board, vs and va exact voltages are marked on a sticker on the panelLeave a comment:
-
Re: XBOX 360 Advice Needed
Having fixed a lot of Xbox I would suggest putting a known good laser in that drive first, I can't remember which way round it is but for some reason (possibly ap2.5 checks) if a ms25 or ms28 will sometimes play DVDs but not games with a failing laser. I think it depended on the exact error I.e play DVD, insert in Xbox 360 or just dumping you back to dashboard. might be worth reading the firmware off the drive to see if it been messed with!
Before you go about glitching console for DVDs key look at the power plug and determine which m/b type you...Leave a comment:
-
Re: LG 50pc1D
i am working on one of theese at the moment, quick question is it possible to remove the ipm from a x sus and put them onto y sus?,( i can remove them with ir machine without damage). I had nothing but bad experience with chinese parts so was thinking of doing the above since xsus boards cheap here in ukLeave a comment:
-
Re: sony kdl-46ex400 red led 6 times blinking
this may help, [url]https://www.badcaps.net/forum/showthread.php?t=47431[/url]Re: sony kdl-46ex400 red led 6 times...?t=47431[/url]Leave a comment:
-
Re: 40" Samsung with White bars, please help!
ive replaced quite a few of the chips,
there not to bad with a hot air setup or rework station, maybe someone in your area can replace the as15 chip for you?
probably be cheaper than a replacment board,Leave a comment:
No activity results to display
Leave a comment: