Philips 52PFL9703, 2 red blinks

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Oehoeboeroe
    New Member
    • Aug 2015
    • 4
    • The Netherlands
    #1

    Philips 52PFL9703, 2 red blinks

    Hi,
    I need some help on a Philips 52PFL9703 television.
    TV was working but after switching to stand-by mode it didn't start anymore...only 2 red blinks. Unplugging mains and re-plug didn't help.
    Red LED in front gives 2 blinks. Once I had it starting again, in that case plug in power and tv starts without issues (also after entering standby mode it can come back). But now again in error state.

    Capacitors look OK, set is about 6 years old.
    As I read in the forum, it might has to do with stability/level of 3v3 power in standby mode. So I would like to check that…but how?
    Can anyone provide me with schematic or service manual?

    I only have the type number, not sure how to find chassis number.

    Thanks in advance.

    Patrick
    Tags: None
    • Oehoeboeroe
      New Member
      • Aug 2015
      • 4
      • The Netherlands
      #2
      Re: Philips 52PFL9703, 2 red blinks

      Some more info...
      When start in sdm mode ( by shorten SDM pin to GND) the red led in front blinks 1 long pulse and 9 short pulses.

      What does this mean... I can find very little info on this type.
      SSB is a 3104 303 51026/3104 313 62146

      Any help would be appreciated

      P.
      Attached Files
      Last edited by Oehoeboeroe; 08-30-2015, 07:27 AM.

        Comment

        • Oehoeboeroe
          New Member
          • Aug 2015
          • 4
          • The Netherlands
          #3
          Re: Philips 52PFL9703, 2 red blinks

          Ok, thanks. Indeed seems to be a Q529.1E LA chassis
          Should i indeed suspect Dc/DC on ssb?

            Comment

            Previous template Next

            Related Topics

            Collapse
            • Seb932
              LG 49UB850V not switching on / standby LED off / LD701 blinks 5x
              by Seb932
              Hi,

              i'would like to fix my not working LG 49UB850V tv.

              Symptoms:
              -AC plugged in, Standby LED not working
              -Switching on, Standby LED blinks 3x. LD2300 on mainbord lights up and after ~30s LD701 on PWS board starts to blink 5x repetetive

              Checked already:
              -Powersupply Output in Standby => 3.5V ok
              -Switching On => PWR_On on P201 goes high and 3.5/12/24V are present on P201

              Any suggestions what to check next?

              Thanks in advance!
              09-14-2023, 06:28 AM
            • Bad_IC
              Philips TV 37pfl5604h/12 no standby voltage
              by Bad_IC


              Hello,
              I have a problem with this TV, the standby voltage is not present. I have checked the components around the IC fsq510's area and they seem to work, also replaced this IC but the problem persists.
              These are the voltages in some pins of IC fsq510:
              Vcc=18v
              D=320v
              Vstr=154v
              Unfortunately, I couldn't find the schematic
              What else could I check?
              Is it possible to provide standby voltage from an external source to allow the TV to turn on?
              Thank you​...
              11-08-2024, 01:07 PM
            • brithepi2k
              Samsung UE75TU7020k No picture, Standby blinks 2 times
              by brithepi2k
              My Samsung UE75TU7020k lights up fine when one of the ribbon cables are disconnected from the main board, lights stay on but not getting half a picture, I do the same with the other ribbon and put the other one in and lights stay on but not getting half a picture. The standby light flashes 2 times then reboots then it then tries to come back on again and just keeps looping until I take either one of the ribbon tables out (doesn’t matter which one I take out it stays lit when either one is out). I’ve tested the backlights but all working with none shorting out, I’ve replaced the main board...
              2 Photos
              04-23-2025, 10:05 AM
            • jasonbay13
              Philips 37HFL5682L/F7 no standby light, incomplete service manual?
              by jasonbay13
              picked up a tv and when the power is plugged, the standby light flashes real quick then goes off. of 3.3, 12, 24v is all there but i couldnt find any 5v on the back-end board. ON/OFF is low, which it seems is what turns on the backlight so i removed the wire at the back-end board and put a 10k resistor to the 3.3v, which when plugged in brings on the backlight for a split second and also a blue light "LED1" on the inverter board, which goes off after a short time.
              am i missing something to bring on the backlight or is the inverter/ccfl gone bad? would that cause the inverter board...
              http://cerealbargain.duckdns.org
              12-01-2023, 09:55 PM
            • cekanayake
              L65X1Q_DHS / BN44-00627A Samsung UN65F6400AF Standby blinks twice five times
              by cekanayake
              I am a noob with some elementary knowledge trying to fix this TV that I have no history on. Any help or guidance will be much appreciated.
              When I first examined it was completely dead. saw that the fuse was blown and the ICM801CS blown. I searched and found that the FSFR1800HSL might be the replacement and got one from ebay and replaced it. But when I pulled the ICM801CS I could see the last 3 letters on the blown up part was XSL. So may be I replaced it with the incorrect part. I fixed the fuse and turned it on and it now gives me a standby light blinking twice five times, then clicks...
              04-19-2023, 08:37 AM
            • Loading...
            • No more items.
            Working...