Samsung UN46EH6000 LED ERROR Codes

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • Michale32086
    replied
    Re: Samsung UN46EH6000 LED ERROR Codes

    Originally posted by tom66
    They mean nothing. It is not an error code.

    Most likely open circuit LED strip, or short circuit LED to chassis.
    Yea, that turned out to be the problem with a previously mentioned Westinghouse I worked on..

    OK, disassembly it is...


    Originally posted by tom66

    I don't think that's a factory cut.......
    Well, it WAS until I spliced it to see if that was my problem..

    Yea, probably not the smartest move, I realize...

    Thanx for the response...

    Leave a comment:


  • tom66
    replied
    Re: Samsung UN46EH6000 LED ERROR Codes

    They mean nothing. It is not an error code.

    Most likely open circuit LED strip, or short circuit LED to chassis.

    That will cause a Samsung to cycle the power or fail to boot.

    I don't think that's a factory cut.......

    Leave a comment:


  • Michale32086
    started a topic Samsung UN46EH6000 LED ERROR Codes

    Samsung UN46EH6000 LED ERROR Codes

    I have a nice UN46EH6000 that I have tried 3 different power boards on. All three produce the same response.

    When plugged in, I hear the SAMSUNG tones, but absolutely no light on the screen at all..

    On the power button (a PS3 style thumb button) a red LED blinks 6 times..

    I was going to tear down the unit to the bare bulbs and see if the problem lies there but before I do, I wanted to see if those Error Code Blinks mean anything else.. GOOGLE was no help..

    Also, on the cable between the power board and the video board, there is a trace that had been factory cut...

    Any hints would be appreciated...
    Attached Files

Related Topics

Collapse

  • AK_777
    Sony KD-65A1 Repair – 4 Red Blinks Error
    by AK_777
    Hi everyone!
    I have a Sony KD-65A1 TV with a fault – 4 red LED blinks. After disassembly and visual inspection, I found that the G76 power board and DKA board had been replaced. It is also possible that TCON was replaced, but I am not sure – there are a few marker marks that could be factory-made.

    Based on assumptions, the previous service attempted to solve the issue by replacing potentially faulty components. I decided to investigate further, found a service manual, and figured out a way to power up the power supply unit autonomously and put the OLED panel and...
    02-20-2025, 04:15 PM
  • Sus256
    HISENSE 65E7KQ PRO - no boot
    by Sus256
    Hi all!

    HISENSE 65E7KQ PRO
    RSAG7.820.13512 - chassis
    MT9618BAATAB - cpu
    RSAG7.820.12059 - power
    HD650Y3U77 - panel
    KLM8G1GETF - emmc

    The TV does not turn on, the standby indicator is on. All voltages are present.
    Emms is dead. Not readable, not detected.
    Replaced emmc.
    But with another dump there is no launch

    Terminal log

    UART
    <
    AC_ON
    RPMB key is not yet programmed

    HASH1_VERSION=0x00000000 64bit
    E-B
    FDE enabled
    layout pattern onebin by SAR7,0...
    06-01-2025, 02:11 AM
  • brithepi2k
    Samsung UE75TU7020k No picture, Standby blinks 2 times
    by brithepi2k
    My Samsung UE75TU7020k lights up fine when one of the ribbon cables are disconnected from the main board, lights stay on but not getting half a picture, I do the same with the other ribbon and put the other one in and lights stay on but not getting half a picture. The standby light flashes 2 times then reboots then it then tries to come back on again and just keeps looping until I take either one of the ribbon tables out (doesn’t matter which one I take out it stays lit when either one is out). I’ve tested the backlights but all working with none shorting out, I’ve replaced the main board...
    04-23-2025, 10:05 AM
  • Caimano
    hp Pavilion 14 CE-1XXX 5 fast 3 slow blinks or cmos checksum error if restarted immediately after shutdown or suspend
    by Caimano
    hp Pavilion 14 CE-1XXX
    MB G7AD-2G DAG7ADMB8D0 REV D
    Processor i5 8265U

    AFAIK schematics or boardview are not available for this MB, but I used a similar board as a reference (G7AL-2G)

    Laptop came in not booting with caps lock blinking 3 fast- 2 slow indicating RAM error. Charging works fine. Found bad soldering on the only ram socket present (2 outer left pins and 2 outer right pins).
    Once soldered the laptop started fine and I was able to install Windows 11, upgrade BIOS to version F30 from Windows without a problem, BUT I found a strange and annoying...
    02-06-2024, 10:14 AM
  • Grunder
    Samsung UA55NU7100 2 blinks then reboots
    by Grunder
    Hi please some assistance with my Samsung UA55NU7100 that is stuck in reboot.
    I've read the post by Itelite on a Samsung UA65NU6900 with the same problem but this main board is different and doesn't have the 25v VGH voltage which was the problem that he had.

    There is no legend indicating voltages on the socket/ cable going to the main board just a link marked 11.80 volts. This voltage reads 12.71v. Pins 3 to 9 also 12.71v. Pins 2,6,8,10,11 & 12 all 0.0v. Pin 1 fluctuates 3.01 to 0.0 volts and pin 4 fluctuates 3.25 to 0.0 volts.

    The cpu gets very hot after 10...
    01-26-2024, 07:43 AM
  • Loading...
  • No more items.
Working...