Having difficulty getting hold of schematic diagram of the SC/Ysus board used in this receiver ( TNPA5335 ). Anybody got a copy?
-
Last edited by satinser; 05-29-2014, 06:55 PM. -
Re: Panasonic TXP50VT30 ysus repair
That should be a good one to use. Most of the PDFs now are no good, lucky to find this which is more detail than normal.
there's quite a few kits out there for clues too -
Re: Panasonic TXP50VT30 ysus repair
The SC board was s/c on SC2 caused by all the following components going s/c D421,Q403,Q402,Q401,D401,Q423,Q422 and Q421. Fitted the repair kit and also replaced Q531 and ic502 included in the kit as a precaution. Followed the correct procedure by linking SC50 and the board worked ok without SD and SU connected. Connected SD and SU boards and removed SC50 link. Everything worked fine for 15 -20 minutes then 7 blink error code started again. On checking all the above replaced components had once again gone short circuit.
Any body know the most likely cause for this to happen?Last edited by satinser; 06-08-2014, 11:24 AM.Comment
-
Re: Panasonic TXP50VT30 ysus repair
Any help or advise re above would be appreciated.Comment
-
Re: Panasonic TXP50VT30 ysus repair
Tough one to give much advice on. Bit like knowing why these fail in the first place.
getting 15 -20mins then same failure, makes me wonder whether a part was overheating and then failed, bad earthing screws, or substandard parts/fakes?
Any tech support from the kit provider?
Someone had a moduslink board fail fairly quick, sent it back, got it repaired again and second time round seemed ok. Forget which series, 2011/12?
Not that I'm suggesting getting another kit from the same supplier.
If the picture was fine, I would be inclined to assume the screen and buffers were ok.
Maybe ditch repairing it and see if you can score an original board instead.Comment
-
Re: Panasonic TXP50VT30 ysus repair
Appreciate your comments. I also belief its heat related which is also I in all probability the reason why they fail in the first place. I bought the repair kit from an Ebay seller but have now ordered individual components from Charles Hyde ( trade seller) and in so doing paid about 50% less.
I belief that the dissipation of heat from the rear of the component to the solder pad on the board is the all important factor that could lead to premature failure if not soldered tight to board. I will have to pay more particular attention to this when the components arrive. I will keep you informed of the outcome.Comment
-
Does anyone have service or repair manual for Panasonic RA-6500 or RA-6600 combo radio receiver?05-18-2025, 11:19 AM -
I have an LG plasma that after reading through a bunch of posts and doing some testing I believe has a bad YSUS board. The problem is that that doesn't make sense to me for some of the symptoms. The problem started yesterday. While watching a movie the TV just shut down like I pressed power. I have it hooked to a PC and use RS232 to turn it off and on so I thought maybe something had glitched there. I turned it back on and finished the movie with no problems. The same thing happened today so I checked logs to see if something in the control glitched and sent an off command but it didn't, After... -
I picked up a Panasonic NH-P70G2, though it would apply to the NH-P80G2, NH-P70G1 and NH-P80G1 models as well, as maybe some other models. This one was coming up with a H86 error. After lots of testing and googling it was an error with one of the thermistors in the condenser area.
The attached French service manuals is incorrect, TH11 is gray and is a 95k thermistor and TH12 is black and is a 35k thermistor.
In my case TH12 was bad. I was able to get a 35k thermistor on AliExpress. It's 6mm in diameter.
Unfortunately the whole machine has to come apart to fix it.
I have... -
Copying DMI information from an old bios to a new one is difficult for some members, often they have no experience with a hex editor,or some that have tried find it too hard.There is an option to make things easier for those members so that they don`t need to post their own bios backup for the DMI copying.
Experienced bios modding members can help by posting in other threads the DMI offsets,macro script generated by the software and a download link to the software at softpedia mentioned in this guide,or post your macros in the comments here with a link to the bios request thread .... -
Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing here🤔?
Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting 😂.
TV Model: Panasonic TC-P55ST50
...11-20-2024, 08:52 PM
Comment