Re: Panasonic TC-P50G25 10 blinking light failure.
Quick Question. I have P50G25 TV with 4 Blink on initial power up after plug in that goes to 10 blink after I try the 8 second clear. I tested a short on the P11 which goes away after removing SC20 that tells me it is the SC board. Can any revision of SC board be used to replace? I have a board with no revision but it looks like the AH rev board is the most available. I assume I would install and flash via the SC card.
Thanx,
Ray
Panasonic TC-P50G25 10 blinking light failure.
Collapse
X
-
Re: Panasonic TC-P50G25 10 blinking light failure.
Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
What are the resistance test points for the SD and SU boards? The last thing I want is a freshly repaired part blowing up!Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
I haven't tried the other test yet, but its a bit late here now to rip apart the TV again. As for repairing it myself, I really don't have the patience, plus my surface mount soldering skills are umm.... a bit lacking. I'm also afraid of pulling traces on this PCB, it feels like its going to break by just picking it up!
If you checked the P15V at the P board and it was short and cleared with Sc20, that would be good enough for me.
I forget if you have but resistance test the Sd/Su boards before you fit a working SC board, they can fail and I've had one with shorted SC/SD/SU all together.Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
I haven't tried the other test yet, but its a bit late here now to rip apart the TV again. As for repairing it myself, I really don't have the patience, plus my surface mount soldering skills are umm.... a bit lacking. I'm also afraid of pulling traces on this PCB, it feels like its going to break by just picking it up!Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
Other victims are DG402RP,DG502LW,30F125,45G128.
Did you try the other test and have it turn on with no 10 blink?
If you have not read and interested, over 200 posts of TNPA5081 repair
https://www.badcaps.net/forum/showthread.php?t=26322Last edited by tw2005; 09-29-2014, 03:46 PM.Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
Quite a few have and most reports are good. I think I've read of one return on a different SC board that came back still faulty. Some take the time to report it here.Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
Resistance on SC2 tests 1.5-2 mega ohms.
Q661 tests as follows
E-G = short
C-G = open
E-C = shortLeave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
The set definitely has the AF board. Anyone here use modus to rebuild their board? I haven't come across any reviews of this company's services.Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
That can happen, if it went low enough you'd have 4 blinks, have read with people at 10 then 4 maybe if the board keeps getting powered it may short it more. self repair is not impossible but I think you have rev Ap which is a little cheaper at modus but they should be the same cost.
Actually looks like it's AF rev. Either will work in this setLast edited by tw2005; 09-29-2014, 09:18 AM.Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
Ok , well I guess I won't hang around waiting, it's 1241am here, I'll check where you're at when I get upLeave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
I'll double check tonight, but I recall it was pretty high, in the mega ohm range. I have the SC board pulled out of the set already, so testing Q661 shouldn't be a problem either.Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
Alternate to the above, TV off, disconnect, Sc2,SS11, P35, remove the 3 white flat ribbons on the A board. turn the Tv on as normal, if it strats up normally and no blink codes, A and PSU are good, Vsus at P2 could be checked (200v) and any other voltages, if the optical jack on the A board is lit red, that would mean it's running too. Only leave it on long enough to check, 30 secs or less. don't do what someone else did and leave it running , it will eventually fail and go 4 blink. manual says no more than 30 secs.
there will be no display, some expect to see something.
Don't reconnect any power cable especially p35 for 5 mins or zap and could spike panel which would be very bad and terminalLast edited by tw2005; 09-29-2014, 08:58 AM.Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
Bumping this thread,
I have a TC-P50G25 (US model) here with the 10 blinks code on power on.
Using the diagnostics PDF found here, I determined the TV has a short in the P15V line (reads 15-20ohms on my meter). Following the P15V flow chart, removing the SC20 ribbon cable resolves the short (meter jumps into the k ohm range), which Panasonic indicates is a failure of the SC board.
Testing Vsus reveals no shorts, and testing across the SC2 connector reveals no shorts as well.
Does this definitely point to the SC board as being bad? I'm looking for some confirmation before I send the board out to be repaired as this doesn't look like the same common failure these boards tend to suffer from.Last edited by tw2005; 09-29-2014, 09:28 AM.Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
Bumping this thread,
I have a TC-P50G25 (US model) here with the 10 blinks code on power on.
Using the diagnostics PDF found here, I determined the TV has a short in the P15V line (reads 15-20ohms on my meter). Following the P15V flow chart, removing the SC20 ribbon cable resolves the short (meter jumps into the k ohm range), which Panasonic indicates is a failure of the SC board.
Testing Vsus reveals no shorts, and testing across the SC2 connector reveals no shorts as well.
Does this definitely point to the SC board as being bad? I'm looking for some confirmation before I send the board out to be repaired as this doesn't look like the same common failure these boards tend to suffer from.Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
To eliminate PSU & A board
try disconnecting the 3 white ribbons at the A board, disconnect P2,P11, p35 and power up.
Should turn on and stay on and then you can probe the voltages
Confirmed normal results are:
stay on for about 30seconds, after which it shuts down and gives me 4 blinks.
Read this if not already.
https://www.badcaps.net/forum/showthread.php?t=36183Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
I really appreciate the help and have to make a correction from my first post were i mixed up the numbers.
p11-pin1-(Vsus) - 200kohms+
p11-pin4-(P15V) - 1.4kohms
p35-pin1-(Vda) - 250kohms
I also disconnected SC2 and measured across those pins and got 28kohms and then with SC2 disconnected.
p11-pin1-(Vsus) - 400kohms
p11-pin4-(P15V) - 1.4kohms
I didn't have time to measure the transistors yet.
try disconnecting the 3 white ribbons at the A board, disconnect P2,P11, p35 and power up.
Should turn on and stay on and then you can probe the voltages
Confirmed normal results are:
stay on for about 30seconds, after which it shuts down and gives me 4 blinks.
Read this if not already.
https://www.badcaps.net/forum/showthread.php?t=36183Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
I really appreciate the help and have to make a correction from my first post were i mixed up the numbers.
p11-pin1-(Vsus) - 200kohms+
p11-pin4-(P15V) - 1.4kohms
p35-pin1-(Vda) - 250kohms
I also disconnected SC2 and measured across those pins and got 28kohms and then with SC2 disconnected.
p11-pin1-(Vsus) - 400kohms
p11-pin4-(P15V) - 1.4kohms
I didn't have time to measure the transistors yet.Leave a comment:
-
Re: Panasonic TC-P50G25 10 blinking light failure.
Completely different TV.... I've done a few of those and they are easily fixed but unfortunately it's not so easy on these sets.Leave a comment:
Related Topics
Collapse
-
by riparoHi everyone, I have a Panasonic OLED TV model 55EZ950E, as soon as I turn it on I don't have any image the LED goes from green to red LED blinking every 4 sec, I found the service manual suggests checking OLED PANEL, PB BOARD, T-CON connectors but it seems like everything ok, I didn't find any burns under the pb board
I attach a link to download the service manual, thank you for anyone who can help me
https://tel-spb.ru/download/?brand=P...0E_LA73.rar -
Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing here🤔?
Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting 😂.
TV Model: Panasonic TC-P55ST50
...1 Photo11-20-2024, 08:52 PM -
by ItepKHey everyone!
I've gotten this TV for free, neither have it seen a TV repair man, neither have it been opened before.
This post describes my entire troubleshooting process of this TV.
When I turn it on using the ON/OFF switch at the side of the TV, the light rapidly flashes green, then it stays on, but it does not react to any of the remote buttons, side buttons, and doesn't play audio.
I've taken the unit apart, and I've started to check some voltages:
- On the P11 connector, there is 15V DC only for a brief moment, then it goes
-
by TofHello everyone, here is the issue I am facing with my Panasonic Oled TX-65FZ800e.
When the TV has not be used for some hours, I power up the TV with a video input and the image is displayed perfectly for 30seconds and then the TV switch off with the red light blinking every 4 seconds for ever.
The service manual explanation: EVDD_SOS (EVDD 24V error) with check point (oled panel, P board, A board, T-CON)
I opened it and found a burned connector on PB-board on the 24V pins.
The 24V wires have change a bit of color due to the overheat and the corresponding... -
by itachiHello good people, I have another unit here which is giving me problems. Upon plugging the unit it, after a few seconds the front LED will start blinking 3 times in a row and repeating indefinitely. No image or sound.
The first thing I checked was the backlight. It's a single vertical strip on one side of the panel which has 8 groups of 7 LEDs. (Part #V500D2-LS1-TREM3) I used a backlight tester and each group lit up without issue.
The standby 5.3V is good, the 16V and 24V from the PSU board both come up for a few seconds while the TV_SUB_ON signal is high. Both 16V and... - Loading...
- No more items.
Leave a comment: