LG 50PJ350 dead, relay clicking

Collapse
X
Collapse
 
  • Page of 3
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 template Next
  • zape
    Senior Member
    • Jul 2017
    • 176
    • USA
    #41
    Re: LG 50PJ350 dead, relay clicking

    Yes that's exactly what I experienced with the replacement board,
    The same FETs are blown. The buffer board is not shorted, so I'm a bit confused. Could this be something else, like panel?
    I did find a schematic of a similar Y-SUS board if that helps
    see attached
    Attached Files
    Last edited by zape; 08-21-2020, 05:04 PM.

      Comment

      Previous 1 2 3 template Next

      Related Topics

      Collapse
      • sam_sam_sam
        Mitsubishi CNC switching power supply board dead / relay board bad diode failure
        by sam_sam_sam
        I was working on this CNC machine today found no keyboard functioning no control relay powering on
        The screen powered on and was giving an operation error but the manual was not very clear about what the error exactly was but with a little bit of troubleshooting and finding out that the control relays not powering on and no keyboard functions we narrowed down to this one switching power supply which of course does not have any indicator LED light they are on the keyboard interface/relay controller board

        Found shorted diodes on main controller relays there are 3 of them that...
        01-07-2023, 05:43 PM
      • beetle1303
        Carver CM-1090 - Power relay clicking on & off, then fuse blown after 20-30 seconds of power cycling.
        by beetle1303
        I gotten a Carver CM-1090 amplifier from a friend who has kept it in storage for decades. Opened it up, thick layer of dust cumulated everywhere. Vacuumed it semi-cleaned, and blown off as much as possible the remaining dust. This is a 220V version.

        On initial powered up with nothing connected - it works with all the lights and button indicator lit up as pressed, etc. I then powered off, connected a CD player into the CD RCA input and powered it on. It seemed to work for a short while and when I turned the volume up and down to see the the VUs works, the power started to clicked off...
        3 Photos
        01-13-2025, 08:49 PM
      • Donny2derby
        LGOLED55B7V Clicking and dead screen.
        by Donny2derby
        Picked this up other week and when I originally looked at in the sellers house I got 3/4's of a working screen and some horizontal lines across the 1/4 of it which was dead/black.

        Just tried powering it up at home and now all I'm getting is a clicking and some very faint lines on 1/4 of the screen whilst the entirety of it is dead.

        When using the remote I get two red clicks on the standby. Not sure if this means anything or helps. The same when I use the manual power up.

        Help appreciated. I'm an electrician, I've fixed a few in the past so not a total...
        08-10-2023, 04:23 AM
      • jimbofz
        lg 60 ph670v dead clicking relay
        by jimbofz
        what a life
        one day a 24inch pana lcd light as a feather then next this monster ,
        i have to stand on a stool to see my mirror at the back of my bench .
        this lg 60 plasma ,relay continuous clicking,
        i soon traced fault to y sus board short cct on the vs .
        i removed board to do cold checks ,the 6 mosfets igbt srjp30h 2a were s/c
        q402 q412 q565 q403 q564 q569 .
        also q505 fet k8a60da .
        i soldered the coils that can go dry l441 l442
        i checked the blue disc ceramic caps ,as re Alisters post where his blew up
        after rebuilding ,tea went...
        09-06-2020, 11:58 AM
      • zwarder
        eax61319402 50PJ350 YSUS
        by zwarder
        Hi
        Had shorted YSUS

        Q24 RPJ63F3
        C726 cap
        Q11 K3667
        R528 & R529 2.2 ohm

        replaced all of these but still trips psu VS & VA are a bit low when ysus disconnected. IC301 does look a bit burnt however

        ZSUS is also good as far as I can tell

        Anyone could help me out on this one
        10-23-2023, 08:11 AM
      • Loading...
      • No more items.
      Working...