sharp lc32l400m

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • willyam1
    Senior Member
    • Feb 2012
    • 112
    • israel

    #1

    sharp lc32l400m

    hi.
    problem no sound in all inputs.
    when I touch in my finger in the smd ic amp ther a noise in the speakers that means that the amp is om no inp signal in the ic( pin 3and 7).
    try even the manu reset and the factory reset no joy.
    am I missing something in the reset procces or just to order the main board.
    thanks willyam1

Related Topics

Collapse

  • Mitike
    SHARP LC-70UC30U starts up with RESET then turn off and blink 1 LONG 1 SHORT
    by Mitike
    Hello guys,

    I have SHARP LC-70UC30U which won't turn on and the stand by LED blinks the 1 LONG 1 SHORT error
    According to other sharp SM-s it is lamp error (I can't find SM for this model)
    And yes I checked other blink error threads on the forum about other Sharp models and still can't make it work.

    If I unplug the set and hold the POWER and INPUT buttons while I'm plug it back the set fires up and shows sharp logo and after that the Android logo and turn itself off again and starts the blinking and wont turn on again except if I do the RESET procedure again....
    02-16-2020, 08:11 PM
  • odie34
    Sony OLED XR-77A80J - 5 Flashes But Turn On After Hard Reset
    by odie34
    I am a hobbyist (not a professional) so please be gentle...

    I recently received an XR-77A80J that wouldn't turn on. (Repeating 5 flashes when plugged in.)

    I did a hard reset by holding the power button for about 30 seconds until the set powered down. I then tried to turn it on and it powered up, bringing me to the setup screen. There's not a lot of detail on the setup screen but the picture didn't have any distortions, so at least a cursory examination suggests no physical damage to the screen. The set appeared to be working normally, but it shut down after about 15 seconds,...
    02-18-2024, 09:11 AM
  • ictc
    Philips MDP 3380/12 Blu-ray Player – No Power, Reset Signal Always High
    by ictc
    I'm troubleshooting a Philips MDP 3380/12 Blu-ray player that shows no signs of life. The display remains off, and no buttons respond.

    Inside, the power supply is working correctly, and all expected voltages on the mainboard match the service manual specifications. The CPU warms up slightly (checked with a thermal camera), the crystal oscillator is functioning, but the reset signal remains high at all times.

    The reset circuit appears to consist of two NPN transistors, one driven by 5V VCC and the other by 3.3V STBY, as shown in the attached schematic. Should the reset...
    02-25-2025, 12:15 PM
  • kotel studios
    ASUS M5A78L-M LX - PWR button works sometimes, CPU stuck in reset
    by kotel studios
    Hi,
    Firstly I'd like to apologize if this was posted in the wrong forum (I'm new here )
    Recently I got an ASUS M5A78L-M LX board in a scrap lot. Saw one broken cap which I've replaced. No broken traces and missing components. While soldering a new cap a bit of solder got onto components bellow SB (opposite of the two lythic caps). Didn't see it and powered the board on.
    I was greeted with it not starting. Came back to it a day later and shorted the PS_ON with GND to force it on. It sprung to life but with CPU stuck in reset (it was an FX 4600 I believe). Thats when I saw the...
    12-14-2024, 10:48 AM
  • MyBrainIsAStrainer
    Asrock H87-Pro4 Rev. G/A 1.04: Power cycling on reset only
    by MyBrainIsAStrainer
    Hi!

    I have a weird one for you. I have a H87-Pro4 from Asrock that power cycles. But only when you do a restart after it was already running!

    Symptoms in detail:
    1. I switch off the ATX PSU for ~15-20 seconds, then switch it back on again.
    2. I press power button. The board boots without issues.
    3. I can shut down the board any way I want (via OS* menu, or pushing the power button - either in the OS or the boot manager).
    4. Push power button again, board boots fine.
    5. This shutdown/powerup can be repeated multiple times without problems.
    6. BUT: If I do a restart instead
    ...
    06-25-2023, 02:44 PM
  • Loading...
  • No more items.
Working...