Bush IDLCD32TV16HD - 2 seconds to black

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • tom66
    EVs Rule
    • Apr 2011
    • 32560
    • UK
    #1

    Bush IDLCD32TV16HD - 2 seconds to black

    Had fixed the 26" recently.
    Same fault on 32" -- slightly differnet symptoms but same cause, two bulging 10uF/450V
    IPOS 150 power supply, I think

    Interestingly, this one has had the 10uF/450V replaced before with Panasonic NHG, I think those are not good enough, so I am using Panasonic ED. (The replaced Panasonic were bulging.) Either that, or this PSU design is so crap it can kill decent Panasonic caps!
    Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
    For service manual, schematic, boardview (board view), datasheet, cad - use our search.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • APOPAP
      Panasonic National NV-M3 VHS Camera shuts down after some seconds
      by APOPAP
      Hello everybody,
      First post here. I have been reading posts here for some time now, but today I made my first account and post.
      The same question is also posted on another site, here it is:

      Just found an old Panasonic National NV-M3 VHS Camera without the original charger but with a special bag with a led, switch and fuse that is designed for a lead-acid 12v 6Ah battery. It has two cables coming off the bag that leads to the camera terminals (Only + and - ). Pretty sturdy design I think.

      I tried connecting it to a Computer PSU (12.7v) but I get battery error...
      08-25-2025, 10:12 AM
    • PanasTC
      Panasonic TC-60CX800U turns off after 2 seconds.
      by PanasTC
      Panasonic TC-60CX800U with Power board: TNPA6060 1P
      The TV starts, the LED lights blink for 2 seconds, and the TV turns off; I tested the voltages on the powerboard, and it looks ok.
      Also, I could see HDM in the top corner for a second.

      Is it possible that the issue is a bad LED light that forces the TV to turn off?โ€‹
      11-27-2023, 09:02 PM
    • Andre Gilbert
      Panasonic TC-P55ST50 8 blinks then no blinks
      by Andre Gilbert
      Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing here๐Ÿค”?
      Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting ๐Ÿ˜‚.

      TV Model: Panasonic TC-P55ST50
      ...
      1 Photo
      11-20-2024, 08:52 PM
    • zklgfs
      Anker SoundCore 2 Bluetooth Speaker Turns Off After a Few Seconds (Possibly Firmware Issue?)
      by zklgfs
      Hi,

      I have an Anker SoundCore 2 (A3105) that I saved from the trash (well, I guess there's a reason why it was supposed to go into the trash...). The problem is that it always turns off after a few seconds (sometimes it stays on a bit longer, between 30 and 60 seconds, but it still turns off). The power light turns on and the bluetooth light starts blinking, but both abruptly turn off again. The "turn off sound" is still played after the lights turn off. Sometimes, it also loops the on-off cycle several times without me pressing any buttons. If I connect an AUX cable, music...
      08-11-2025, 02:14 PM
    • twonk9098
      Lenovo Legion 5 high fan spin turns off after 34 seconds
      by twonk9098
      Hi all,

      I have a Lenovo Legion 5 with a Ryzen 7 series CPU and RTX 3070 GPU. My issue is that it turns on and all seems fine except after a few seconds the fans spin up high and the laptop turns off after 34 seconds.
      I can get into bios and can even boot and login to Windows however after 34 seconds no matter if Im at the bios screen or booted into Windows it will just turn off.

      I have managed to run HWmonitor and the temperatures of the CPU and GPU are fine, I can also touch the heatsync which is warm but not hot.

      I have tried a few new bios but exactly...
      07-14-2024, 11:19 AM
    • Loading...
    • No more items.
    Working...