Crosley lcd possible power supply problem

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • electronicsurplus
    Badcaps Veteran
    • Jun 2012
    • 210
    • USA

    #1

    Crosley lcd possible power supply problem

    I have a Crosley LCD, which is in some sort of standby, green light is constantly blinking. Has 5V but, no 24V or 12V.

    Tried jumping 5V STB with PSon and, BO pins, still no 24V or 12V

    Also noticed blown fuse on Slave Inverter

    Does anybody know about these power supplies or, where in Power Supply to determine what is wrong?

    I cannot locate any service manual or schematic for this set

    Thank you

    any help will be greatly apppreciated

    Jon
    This Forum absolutely the best and, the most helpful forum I have ever found anywhere. thanks to all the fantastic members here
    Help keep these from the landfills
  • JimmysTGP
    Member
    • May 2012
    • 45
    • US

    #2
    Re: Crosley lcd possible power supply problem

    If you can take some good quality pics of possible PS and Inverter boards and Pics of numbers located on the boards.

    Comment

    Related Topics

    Collapse

    • sam_sam_sam
      Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
      by sam_sam_sam
      I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

      One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
      03-31-2024, 02:12 PM
    • sam_sam_sam
      Modification to a ZD-987 desoldering/soldering station using a external switching power supply
      by sam_sam_sam
      I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

      I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
      07-01-2024, 06:34 AM
    • Tynan Dill
      Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
      by Tynan Dill
      I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

      Upon bringing it home and plugging it up, it showed a standby light.

      I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

      The screen seems to blackout and stay black, but with a flashlight I can see the display.

      With my Playstation 4 connected via HDMI, and running a game I can hear sound.

      Assuming...
      11-22-2024, 01:46 PM
    • JimBanville
      Definitive technology SC 2000 subwoofer amp's power supply clicking and popping
      by JimBanville
      The sub developed a constant popping every couple seconds from woofer and power LED flickering with nothing but wall AC connected. Connecting an audio cable didn't change anything. It doesn't play but a second or two of audio in between the pops.
      Opened it up and discovered the power supply is making a faint clicking or ticking sound.
      I measured the amp's output to the woofer and it pulses up to 50mv DC to be driver. The pulses coincide with the power supply ticking/clicking.
      I measured the power supply output going to the amp board and it too has this pulsing. Voltage cycles...
      09-13-2023, 07:21 AM
    • chth96
      What capacitor should I purchase for Power Supply of obsolete game consoles?
      by chth96
      hello.

      I have Sega Saturn and 5 years ago, I recapped all of capacitor in the Power supply, Because At that time, It frequently freezed black screen after SEGA logo displayed.

      It hardly ever freezed after I finished to recap all of caps in the power supply.

      But Yesterday, It did not show any screen at all and its green power LED constantly blinked.

      To my surprise I found that all of two NXH 10v 2200uf capacitors in the secondary area of Power supply have been bulged and It measured 57 mF and 75 mF capacitance.

      It seems that quality...
      10-01-2024, 08:14 AM
    • Loading...
    • No more items.
    Working...