Re: pioneer plasma PDP-435PE
Tom i was taken all the pin out readings & pics but keep getting timed out on this site..is there a setting on this site cos it does my box in..i aint a fast typer lol
-
Re: pioneer plasma PDP-435PE
http://i1068.photobucket.com/albums/...5/P1000965.jpg
http://i1068.photobucket.com/albums/...5/P1000970.jpgLeave a comment:
-
-
-
-
-
-
-
Re: pioneer plasma PDP-435PE
Hi tom..how do i download that manual..some pics of the pin outs..am i testing the voltages with all the plug leads in thx
http://i1068.photobucket.com/albums/...5/P1000937.jpg
http://i1068.photobucket.com/albums/...5/P1000936.jpg
http://i1068.photobucket.com/albums/...5/P1000935.jpg
http://i1068.photobucket.com/albums/...5/P1000938.jpg
http://i1068.photobucket.com/albums/...5/P1000933.jpgLeave a comment:
-
Re: pioneer plasma PDP-435PE
http://cgi.ebay.co.uk/ws/eBayISAPI.d...m=290682203608
Why don't you see if you can get this one nice and cheap! He has listed it twice. I would have it if I lived closer.Leave a comment:
-
-
Re: pioneer plasma PDP-435PE
I love Pioneer stuff. You need to find a Pioneer 5090 to fix and keep Tom they are awesome!Leave a comment:
-
Re: pioneer plasma PDP-435PE
Service manual:
Page 58.
Red LED flashing two times indicates MR-AC power off (media receiver power off.) This probably indicates a fault with the AC detect, PFC stage or perhaps another part of the power supply. It may also indicate a media receiver fault.
Start by taking pictures.Leave a comment:
-
pioneer plasma PDP-435PE
Has any1 here ever worked on 1 of these sets..when powered on the led flashes from green to red continuesly..when pressed power button at the side the red led flashes 2 times pause then 2 times..thats with & without the media receiver box connected..on the receiver box the red & green led are on solid when connected to tv..ive not worked on a plasma before was hoping to find bulged caps but all seem ok..the psu is PCB2524 A06-125581
.
-
I have an older Pioneer receiver (VSX-44) that's been dropping the HDMI output (black screen) for a few seconds every few minutes. Setup is HTPC -> Pioneer DVD HCMI in -> Pioneer HDMI out -> Samsung TV HDMI in, all with cheap HDMI cables that have never caused trouble before..
I initially found a lot of play in the receiver's HDMI inputs and output so I kind of squeezed them back into shape and they're making a tighter connection, but the problem persists.
And also, often, the HDMI will drop out in exactly the same way (black screen) just as my central air... -
Hello out there in Badcap land.
I have a Pioneer plasma that gave me the dreaded 8 red blink and shutdown, I have been trying to trace the failure points. On my last inspection while replacing a Y Sustain Board I noticed on the original and replacement board some missing solder, the points of connection
are from the Digital Address Board and the Buffer Boards. I have included the pictures, should I resolder these points or are they unsoldered intentionally? Any help would be much appreciated.
Thank you
Pixelcap... -
Hello. My receiver "seems" to be working fine. It functions as it should. the receiver is the Pioneer vsx-1123. However, while doing some work in the house, I noticed that my HDMI cable from the receiver was registering as "hot" using my fluke non-contact voltage tester.
I've done some troubleshooting to try to narrow down the problem, and all wires (speaker/hdmi/subwoofer) coming from the receiver, whether it's powered on or stand-by, register as "hot". none of my other receivers are experiencing this issue, so it doesn't seem to be an issue with... -
Have a colleagues Pioneer VSX-3300, it wont power on, hasnt for a number of years, but just now trying to figure out what's going on with it.
It has 120V input and I have followed that 120V to a small board that appears to have a small transformer and a relay among a few other components I dont think the relay is changing state which I believe turns on the receiver, but this is all speculation.....
I have downloaded the repair guide, which I have attached to this post, but I am having a hard time following it.... Can someone please offer any advice on what to check?... -
hi i have a receiver that is destroyed from the overvoltage i guess
my question is has three wires u v w for driving a motor fan i found an other receiver wireless from aliexpresss with the same propertiew but for dc motor
the motor fan has not label
i have an other receiver operational
In your opinion can i measure the voltage at the output ?
what do you suggest me with a simple instrument multimeter or using someone instrument more specific ?
thanks in advance...
Leave a comment: