How to Adjust Ysus board (LJ92-01200A) from Magnavox 42MF231D/37????

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Paul678
    Badcaps Veteran
    • Nov 2011
    • 402

    #21
    Re: How to Adjust Ysus board (LJ92-01200A) from Magnavox 42MF231D/37????

    Voltages from the power supply board are within spec.

    But again, if it's only 2 pots that adjust this, shouldn't I have
    gotten closer than I have just eyeballing it?

    Is it really such a SUPER hair-trigger adjustment?

    Comment

    Related Topics

    Collapse

    • tonybig10
      Magnavox MDR515H/F7 And Magnavox MDR537H/F7
      by tonybig10
      Hi is any one can help me on getting the Schematics for Magnavox MDR515H/F7 And Magnavox MDR537H/F7 PDF file thank you I really appreciate it. Just need to change some component on
      the main board and the power supply board. I looked all over for the internet and I cannot find the Schematics sheet for both of them. I don't know where else to look I hope someone can help me...
      03-07-2025, 01:03 PM
    • legg
      LG 42PC3 buffer output doesn't follow YSUS
      by legg
      LG42PC3D -UD originally with green lamp but no display or audio.
      Owner says was working, then went 'pop'.
      All 5V caps bulging. replaced.
      All PSU output voltages within spec but -Vy is low on YSUS.
      One of three parallel fets between SUS_OUT and SUS_DN is zenering,
      eventually shorts DG. Replaced all 3 - -Vy now OK.

      Y scan buffer test point does not follow YSUS output below -50V

      Note: This unit seems to expect YSUS output to park at -Vy in between
      drive signal pattern periods. A replacement drive signal board confirms this....
      11-18-2021, 11:49 AM
    • Truncatedhose
      Help repair this relic? Philips 42PF7220A/37, pulsing buzz from YSUS
      by Truncatedhose
      Greetings all!

      Originally this set had the usual messed up video symptoms such as: horizontal lines, weak, grainy video, bottom and top of picture differ in intensity of problem. It also seemed to slow to turn on or show the messed up picture.

      Seemed like must be YScan/buffer board failure. Ordered buffer boards from my distributor which were supposed to be original/new and also from another distributor, I ordered the YSUS because I wanted to replace it for preventative maintenance. (also, the YSUS had a bulged cap, so there was even more reason to suspect it could...
      07-04-2018, 10:59 AM
    • Mcfeetroy
      homemade speakers AN5277 How to adjust the volume?
      by Mcfeetroy
      Hello everyone. I soldered the speakers according to the circuit diagram on the AN5277 sound amplifier microcircuit. Everything works fine (I only added a ferrite ring to remove the sound transmission interference)
      But I can't adjust the sound (there is no variable resistor or something similar for this in the circuit....Please tell me how I can adjust the sound? What needs to be added to the circuit?

      ​ ...
      10-27-2024, 10:19 AM
    • zwarder
      eax61319402 50PJ350 YSUS
      by zwarder
      Hi
      Had shorted YSUS

      Q24 RPJ63F3
      C726 cap
      Q11 K3667
      R528 & R529 2.2 ohm

      replaced all of these but still trips psu VS & VA are a bit low when ysus disconnected. IC301 does look a bit burnt however

      ZSUS is also good as far as I can tell

      Anyone could help me out on this one
      10-23-2023, 08:11 AM
    • Loading...
    • No more items.
    Working...