Samsung "MU" series (UN, UA, UExxMUxxxx) fault dump IC1604 25Q40...

[Me_you_them]

What program did you use?
NeoProgrammer V2.2.0.10 ?
Did you program the chip through a clothespin or solder the chip through an adapter?

I've used NeoProgrammer V2.2.0.10 and I've desoldered the chip from the mainboard and soldered on the adapter to program it

[lotas]

What program did you use?
NeoProgrammer V2.2.0.10 ?
Did you program the chip through a clothespin or solder the chip through an adapter?

[Me_you_them]

Was this dump native, original, status register (0x88, 0x42) written after recording the dump?

Yes the dump was the original native one, status register done, i followed the instruction on the post #4

[lotas]

Nothing to do....
Standby led turns on and immediately off, sometimes led bars turns on and off imediately

Was this dump native, original, status register (0x88, 0x42) written after recording the dump?

[Me_you_them]

Nothing to do....
Standby led turns on and immediately off, sometimes led bars turns on and off imediately

[lotas]

Hi lotas,
can you help me with this firmware???

Samsung UE55MU6400U
M/B BN41-02568B (BM94-12401R)

Hi, I can, try it.

[Me_you_them]

Hi lotas,
can you help me with this firmware???

Samsung UE55MU6400U
M/B BN41-02568B (BM94-12401R)

[lotas]

What initially happened to the TV? In service mode, at the point you clicked on “Micom Update” and after that the TV stopped turning on?
If yes, then the firmware has been erased in micom, you need to program it.
And also, you have some strange dump 24C512, or it is so badly damaged or poorly read, try this one.

[Ashry]

Where did you get the idea that the problem is in these firmwares, if there is no standby mode and the LED is not on, then a common problem in this chassis is IC204 (stabilizer from 5v to 3.3v) and micom Weltrend, check the resistance at 1.2 pin IC203 relative ground and is there 3.3v power on these pins

Thanks for your your support. i found that sub eeprom (24c02) is connected to this ic1203 so i thought this may be the problem.
I measured the regulator and i/p 5.3 v & o/p 3.3 v so it is good, also the voltage at pin 1&2 3.3v and no short with ground. i tried to press the reset button but nothing happened

how can i check ic1203 (61P805) is healthy ??
does it need programing? if yes can it be done by CH341?

[lotas]

Where did you get the idea that the problem is in these firmwares, if there is no standby mode and the LED is not on, then a common problem in this chassis is IC204 (stabilizer from 5v to 3.3v) and micom Weltrend, check the resistance at 1.2 pin IC203 relative ground and is there 3.3v power on these pins

[Ashry]

Dear Sir can you help me with dead main board ( BN41-01587) for Samsung ua40d6400un and power board (BN44-0427A)
i uploaded the flash files from 24c02 (IC 1205) & 24c512 (IC 1401)
A5 & 3.3 vdc are exist.
thanks in advance.

[Ashry]

Hello
Please I need your help with this mb bn41-01587e
5vdc exist but standby led not light and no action with power button


IC 1401 should be reprogrammed or what?

[lotas]

Hi Lotas, my TV model is UN50MU6100GCZB, Board Code: BN41-02568B from Argentina. I'm having the same issue as another user before. The standby LED turns on for 1 sec every 15 sec. When Flashing an incorrect bin, the board stays completely dead. So I guess it could be bios related. could you help me? Thanks in advance

Strange damage to the dump, usually if in this series the MU dump is damaged at the beginning of the dump, then the TV's standby LED does not light up at all. Try this one, I adjusted it a little, and don't forget about the status register after recording the dump.

[juani981]

Hi Lotas, my TV model is UN50MU6100GCZB, Board Code: BN41-02568B from Argentina. I'm having the same issue as another user before. The standby LED turns on for 1 sec every 15 sec. When Flashing an incorrect bin, the board stays completely dead. So I guess it could be bios related. could you help me? Thanks in advance

[murtagh]

Thank you Lotas, much appricated.

[lotas]

Hi Lotas UE55MU6172 IC401 can you fix please.
Regards,
Pat.

I can, but it (dump) is working for you, your problem is not in it.

[murtagh]

Hi Lotas UE55MU6172 IC401 can you fix please.
Regards,
Pat.

[srdi]

Try.

Thank you very much!! Everything is working!

[lotas]

The TV does not turn on, there is no standby mode! SAMSUNG UE55mu6192 ver01

Try.

[srdi]

The TV does not turn on, there is no standby mode! SAMSUNG UE55mu6192 ver01