Hello i need help i have kyocera m2030 it posts a code f010
thank you
thank you
-
-
Re: kyocera m2030 ERROR F010
can you help me I am new to this field -
Re: kyocera m2030 ERROR F010
search in the service manual of M2030 to find out what the code f010 means.Comment
-
Re: kyocera m2030 ERROR F010
Thank you
this is a problem of the main motherboard i have makes a small search i want to know how i repair this card mother there are people in algeria repaired these cards mother
i have no idea how to repair themComment
-
Re: kyocera m2030 ERROR F010
can you help meComment
-
Re: kyocera m2030 ERROR F010
krimo firmware problem you have to copy a new file into eeprom 24 * 24 pinComment
-
Re: kyocera m2030 ERROR F010
thank you bro can give me a picture of this eeprom and can i program this eeprom with miniproComment
-
Re: kyocera m2030 ERROR F010
Eeprom firmware m2030dn a programmerAttached FilesComment
-
-
Re: kyocera m2030 ERROR F010
thanks you frindComment
-
Re: kyocera m2030 ERROR F010
thank you aboumohamed can you give me dump of this eepromComment
-
Re: kyocera m2030 ERROR F010
i have the eeprom
the file is too largeAttached FilesComment
-
-
Re: kyocera m2030 ERROR F010
this is the chipComment
-
Re: kyocera m2030 ERROR F010
look thereComment
-
Re: kyocera m2030 ERROR F010
.................Attached FilesComment
-
-
Re: kyocera m2030 ERROR F010
Thank you houssamComment
-
Re: kyocera m2030 ERROR F010
hello I am also looking for the kyocera m2030 dump can someone help me thank you in advanceComment
-
try this dump 100% okComment
-
Hi,
I have a 2014 vintage Philips 60PFL8708S/12 that suddenly died in the middle of the kids watching a show.
The relevant service manual for the chassis is available here.
The TV no longer powers on, and leaving it powered on for a few minutes results in the layer-1 error with 2 blinks.
When I short the SDM to ground I get the layer-2 error code 53.
The inside of the TV has no damaged components and no swollen capacitors.
In SDM-mode when all the power rails are left on despite entering the protection mode, I tracked down and measured... -
when upgrading windows 7 to windows 10 i get this error code (title).then to correct the error i have to enable tls 1.1 and tls 1.2 in registry editor. but there I do not find TLS 1.1 and TLS 1.2 instead there is SSL2.0
in REGISTER EDITOR on windows 7 ad can one do to correct the problem?
Error Code 0x80072f8f 20000 -
Hi all!
HISENSE 65E7KQ PRO
RSAG7.820.13512 - chassis
MT9618BAATAB - cpu
RSAG7.820.12059 - power
HD650Y3U77 - panel
KLM8G1GETF - emmc
The TV does not turn on, the standby indicator is on. All voltages are present.
Emms is dead. Not readable, not detected.
Replaced emmc.
But with another dump there is no launch
Terminal log
UART
<
AC_ON
RPMB key is not yet programmed
HASH1_VERSION=0x00000000 64bit
E-B
FDE enabled
layout pattern onebin by SAR7,0... -
I have a Hitachi HTA-DD3W AV receiver and when I got it I tested it working fine with speakers but it needed a clean inside because it had signs of moisture in it but it was fully dry with bits of wood chips, I guess this was left in a shed so I fully disassembled it and cleaned it with isopropyl alcohol very carefully, some de-soldering was also needed but now its very clean, luckily there was no rust on any components and all the capacitors are fine with no bulging. When I turn it on I hear a relay switch on then a few seconds later another relay switches on or off and the display has a "-PROTECT-"... -
I am currently working on my Crosshair VIII Hero mainboard on which a GPU short occured after which the mainboard would not turn on again. I suspected the VRM Controller (IR35201) and soldered it off. After that the board turned on again, obviously without providing voltage to CPU etc. I soldered a new IR35201 on it but it seems like the board still don't want to boot correctly. LEDs etc. turn on normally and after I press start button the power supply turns on fully and stays on, so I guess no shorts. Also nothing gets really hot. The error code shows code 00 and I measured VCPU and it was 0...
Comment