Delta DPS-286AP (RDENCA336WJQZ) Troubleshooting

Collapse
X
Collapse
 
  • Page of 4
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 4 template Next
  • bznhvx
    Member
    • Mar 2020
    • 41
    • USA
    #61
    Re: Delta DPS-286AP (RDENCA336WJQZ) Troubleshooting

    I decided to give this TV one more shot before parting it out. I bought a replacement PS board. I installed the board and get the exact same error that I got before. I get two LED flashes on the Power and one on the OPC LED.

    The manual says this is:
    DET_10V error
    Power Flashes twice, OPC Flashes once

    DET_10V (57pin). UR10V or A9V is not applied.
    If error is detected during operation, error standby is activated by
    polling.

    Could it be that the original power supply was good but just in "error standby"? I thought that forcing the PS_ON signal would override that, but I'm wondering if perhaps the problem is not in one of the downstream linear regulators on the CPU board.

    I do not see UR10V or A9V on the schematics. The signal on Pin 57 of IC2002 looks to be an output, not a voltage monitor, so it looks like this diagnostic description does not match up. Anyone see this before?
    Last edited by bznhvx; 04-28-2020, 06:53 AM.

      Comment

      • bznhvx
        Member
        • Mar 2020
        • 41
        • USA
        #62
        Re: Delta DPS-286AP (RDENCA336WJQZ) Troubleshooting

        After checking the power supplies on the main board, providing 12VDC to the Unregulated 15 input, they all look good. Perhaps the new PS board I received is also suffering from the same issue.

          Comment

          • Rideau
            New Member
            • Jul 2021
            • 4
            • Canada
            #63
            Re: Delta DPS-286AP (RDENCA336WJQZ) Troubleshooting

            I have a failed Delta DPS-286AP (RDENCA336WJQZ).
            ic7905 (TNY264) blew it's top off. I can replace that but want to replace possible components that created the blown ic7905. I note that various companies offer a repair kit but are often sold out. It includes the ic and a diode plus 2 resistors. I suspect that it may be diode D7908. Does anyone know what that diode is?
            thanks

              Comment

              Previous 1 2 3 4 template Next

              Related Topics

              Collapse
              • howardc64
                TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
                by howardc64
                All left and right refers to looking from rear of TV (or looking from front with TV upside down)
                • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
                • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
                ...
                07-24-2025, 05:17 PM
              • m1ch43lzm
                HP Pavilion 15-eh Board DAG7HAMB8F0 - CPU throttling to 0.4GHz (PROCHOT_EXT) and black screen
                by m1ch43lzm
                Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
                Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic...
                05-12-2025, 08:37 PM
              • Tynan Dill
                Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
                by Tynan Dill
                I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

                Upon bringing it home and plugging it up, it showed a standby light.

                I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

                The screen seems to blackout and stay black, but with a flashlight I can see the display.

                With my Playstation 4 connected via HDMI, and running a game I can hear sound.

                Assuming...
                ORIGINAL POWER SUPPLY BOARD
                7 Photos
                11-22-2024, 01:46 PM
              • Hakuu
                LG OLED77G1PUA - No Video / Audio after a TCON Board change and Software Update
                by Hakuu
                Hi There,

                This TV was auto switching off after few seconds with some vertical lines on the screen, so got a new TCON board and replaced it.

                After replacing the TCON board it was working fine and i set it up with everything, used for few hours, then had the bright idea to update the software on it. During the update process, TV switched off and now no audio or video. No relay switch sound.

                More Details

                TV Model - LG OLED77G1PUA

                Got the same exact TCON board from TVPartsToday and replaced it. But didnt transfer the EPPROM data (didnt...
                07-12-2023, 02:37 PM
              • jb_Bak
                Sony xbr-65x900c main board issues?
                by jb_Bak
                Hey guys great forum glad to have found it. I bought a Sony XBR 65X900C cheaply because it didn't work. No signs of life at all not even a light/led. All I hear is a brief high voltage sound when I throw the power to it.

                Didn't see any obvious signs of damage so right away started checking voltages. This is what I see:
                Power Board Connector that goes to Main board
                CN6401
                Pin 01 NC
                Pin 02 NC
                Pin 03 "BL_ON": 0V
                Pin 04 "N/C"
                Pin 05 "STBY 3.3V": 3.5V
                Pin 06 "GND": N/C
                Pin 07 "AC_OFF"...
                09-27-2021, 04:52 PM
              • Loading...
              • No more items.
              Working...