Standardization of "modular" power supply connectors?

japlytic

Badcaps Legend

Join Date: Oct 2005

Posts: 2086

Country: Australia
#1

Standardization of "modular" power supply connectors?

10-07-2012, 01:19 AM

As far as I know, there appears to be no standard for "modular" power supplies for PCs, which means the detachable cables (remove to save space) are specific to a particular manufacturer and/or series.
If you cannot find these cables, the power supply would be almost useless.

My first choice in quality Japanese electrolytics is Nippon Chemi-Con, which has been in business since 1931... the quality of electronics is dependent on the quality of the electrolytics.
Tags: None
Phaihn

Badcaps Veteran

Join Date: Jan 2009

Posts: 842

Country: Canada
#2

10-07-2012, 01:25 AM

Re: Standardization of "modular" power supply connectors?

i would imagine so.

My Computer.
AMD APU A4-3300 2.5ghz 1mb cache
Motherboard GigaByte GA-A75M-S2V
Kingston HyperX Blue DDR3 8GB (2x4GB)

SB Audigy 2 ZS [B800] Sound Card
500GB WD Caviar® Blue™
1 Terabyte WD Caviar® Black™
2 Terabyte WD Caviar® Black™
Comment
Behemot

Badcaps Legend

Join Date: Dec 2009

Posts: 4845

Country: CZ
#3

10-07-2012, 04:34 AM

Re: Standardization of "modular" power supply connectors?

Well not true so much. If you buy a pack of these cables, there will definitelly be at least a few which can be used directly or in worst case scenario with conductors rearranged. Acquired a few extra cables like that for my Enermax Liberty.

Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts

Exclusive caps, meters and more!
Hardware Insights - power supply reviews and more!
Comment

Previous template Next

Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?

by Tynan Dill

I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

Upon bringing it home and plugging it up, it showed a standby light.

I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

The screen seems to blackout and stay black, but with a flashlight I can see the display.

With my Playstation 4 connected via HDMI, and running a game I can hear sound.

Assuming...

7 Photos
- Channel: Troubleshooting TVs and Video Sources
11-22-2024, 01:46 PM
Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply

by sam_sam_sam

I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
- Channel: General Electronics Technical Discussion
03-31-2024, 02:12 PM
Norstar - Plus modular ICS NT7B62FA power supply repair

by CapLeaker

Patient: Norstar - Plus modular ICS NT7B62FA power supply.
Complaint: Doesn't power up anymore. It did work for a short while, next morning dead?

U1 (UC2844) Vcc pin jumping up and down between 10V and 15V. Vcc supply resistor 51.1k and capacitor 100uf 40V is o.k., but jet there is nothing coming out on the other end. Secondary is producing nothing, no shorts, nothing visible.

Replaced U1 (UC2844) with a new one, powered the PSU up on the bench and the LED started to blink faintly. Plugged the PSU card back into the Norstar modular ICS and all is working...
- Channel: Troubleshooting Power Supplies and Power Supply Design
10-19-2024, 05:06 PM
Modification to a ZD-987 desoldering/soldering station using a external switching power supply

by sam_sam_sam

I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
- Channel: General Electronics Technical Discussion
07-01-2024, 06:34 AM
Seasonic B12 BC-550 – barely 2 years old and with BAD CAPS already!

by momaka

I know I've been a little scarce lately (like the last 2-3 years), but I'm still here and still doing my thing with fixing PSUs.

For today's considerations, I have a Seasonic B12 BC-550 [A551bcafh] 550 Watt ATX power supply for you (click on links for full size images).

https://www.badcaps.net/filedata/fetch?id=3591771

https://www.badcaps.net/filedata/fetch?id=3591772

It's a modern ATX unit with fixed (non-modular) cables and an 80-plus bronze certificate. Here's the label:

https://www.badcaps.net/filedata/fetch?id=359177...
- Channel: Troubleshooting Power Supplies and Power Supply Design
03-12-2025, 03:42 PM
Loading...
No more items.

Standardization of "modular" power supply connectors?

Standardization of "modular" power supply connectors?

Comment

Comment

Related Topics