How to write this bios chip,with 1.8v or 3.3v on mobo 6059a2623101-mb-a02?I use programmer rt809h
-
-
Re: 1.8v or 3.3v on mobo 6059a2623101-mb-a02
6059a2623101-mb-a02 ? are you sure thats the correct board number -
Re: 1.8v or 3.3v on mobo 6059a2623101-mb-a02
6050a2623101-mb-a02 sorry!this is right model board,and i want to know all resistor around bios what ohm have pleaseLast edited by datodati962@gmail.com; 06-20-2020, 05:05 AM.Comment
-
Re: 1.8v or 3.3v on mobo 6059a2623101-mb-a02
To answer your original question, the bios chip is 1.8V 25Q64FWSIG .
Schematic requests go in a seperate sub-forum https://www.badcaps.net/forum/forumdisplay.php?f=41 ,there is no scheme available for this board.
Ask your resistor question in this thread: https://www.badcaps.net/forum/showthread.php?t=67058Comment
-
Re: 1.8v or 3.3v on mobo 6059a2623101-mb-a02
Thank you very much for your reply,it was very helpfullComment
-
This is a shot in the dark, but I was just using my RT809H programmer and it got stuck in a certain state so I power cycled it. Now, the device LED just flashes quickly and does not connect to the software. I've tried to update the BIOS of it and it fails. I went so far as to remove the ROM from the programmer itself but it's some weird chip (I believe ATMEL, but I can't find any datasheet on it) so I've been unable to read the BIN from it w/ my other programmer. Chip has ATMLHC4C56BM CN written on it (I think). I'll upload an image. I have the programmer's BIN ready to program it manually. Anyone... -
hello,
i want to buy a new programmer mainly for use for laptops bios chips and i'm between the Xgecu T76 and the famous RT809H.
i think that T76 is faster wich makes it the best choice for using Pogo pins,i asked the support if it supports Mec ships found on some Lenovo laptops i didn't get an answer yet.
i would like some ideas and which one do you recommend?... -
Hi everyone,
help me please
I have an HL-DT-ST BD-RE GGW-H20N with ROM version: XA02.
When I tried to burn a 25GB Blu-ray disc using ImgBurn, I got an error.
I will share all the details with you, including the disc information.
...Code:HL-DT-ST BD-RE GGW-H20N XA02 (ATA) Current Profile: BD-R Disc Information: Status: Empty State of Last Session: Empty Erasable: No Free Sectors: 12,219,392 Free Space: 25,025,314,816 bytes Free Time: 2715:27:17 (MM:SS:FF) Next
-
dose RT809h programmer support the new Bios chips like 25q256jveq because i have minipro TL866 and icant programming these ics and if anyone can tell me about a cheaper programmer wich do the same job to buy it -
Greetings badcaps community,
I havent done this for a long time and want to start it all again, after some evil and annyoing illness.
So I apologize in advance, if some phrases might sound a bit like gibberish or illogical to you.
Im trying my best to fully describe what I plan to achieve and hope I was choosing the right sub-forum for my new adventure.
I have a Elitebook 820 G1 and a Elitebook 840 G2 here.
These ask for a password when entering the BIOS, but boot just fine from the internal SSD.
I learned that desoldering...10-29-2024, 06:03 AM
Comment