Hello, does anyone have a bios dump for a Panasonic CF19AHUC61M. I do have an email into Panasonic, because it's not listed in downloads, but I think that's gonna be a dead end.
Thanks
Thanks
-
-
Re: CF-19AHUC61M corrupt bios
Can you post your corrupt bios backup . -
Re: CF-19AHUC61M corrupt bios
I can only get it to dump like a 2mb file, wrong tools maybe? I do have another bios locked motherboard laying around, from when I purchased the laptop from ebay. Maybe I can get that one to dump?Comment
-
Re: CF-19AHUC61M corrupt bios
Attached is the only dump I could get, this one is bios password locked though, if the pass is stored in there can it removed or recovered so I may flash over the corrupt bios.
ThanksComment
-
Re: CF-19AHUC61M corrupt bios
My programmer came in and was able to get a full dump of locked bios, but not corrupted one (bad chip maybe). Can someone unlock this please.Comment
-
Re: CF-19AHUC61M corrupt bios
try this...There are 10 types of people in the world. Those that understand binary and those that don't.Comment
-
Re: CF-19AHUC61M corrupt bios
That worked thank you very muchComment
-
Re: CF-19AHUC61M corrupt bios
Actually I am curious, where is the password stored, theres another on ebay sold by the goodwill, I plan on buying for spare parts, its bios locked too. The mk5 motherboards are hard finds without buying form Heartlands.
Thanks.Comment
-
The Samsung S49CG934SU monitor does not power on - no LED indicator activity and no response to power button. However, when 21V power is connected, it immediately draws 0.8A of current with no display output. The motherboard processor gets warm, and there is continuous reading activity from the W25Q128BV BIOS chip.
Suspected Cause:
I suspect the BIOS may have been corrupted during a power interruption while updating the firmware. The official website provides firmware updates, but they can only be installed via USB flash drive.
Troubleshooting Attempts:
... -
Hi all,
My Samsung Galaxy Book 2 Pro 15.6-inch laptop has no display and won't boot.
The charging red LED lights up, but the charging screen doesn't show any indication.
When I press the power button, the blue LED cycles on and off three times, then the screen doesn't turn on, and the device won't boot.
(I've tried removing the battery and resetting the device, but the issue persists.)
NoteBook Model name : Samsung NT955XED-KK51G(Galaxy book2 pro, i5-1240p, 15.6inch AMOLED)
PCB model name : Venus2-15-5G(REV1.2), Venus2-15 ADL NPC
S/N : 5RNK9FFT70... -
Hi
i have dell latitude E7270 with following symptoms:
- takes long time to restart.
- sometimes powers on and then off
- sometimes while working it just dies,
From googling online bios clean could possible resolve this?
i was able to save bios and was going to try bios clean myself but get an below error when i drop it in ME analyzer.(unsure whether this sometimes occurs or could be due to bad/corrupt bios)
As ME analyzer gave me an error i just decided to write bios with a cleaned bios from E7270 bios post.
I reinstall... -
Hi, I have an MSI PRO B660M-G DDR4 board with damaged BIOS and i need a bios dump from a real board, along with MAC, UUID and Serial Number info (eg. a BIOS screenshot and pictures from the board stickers).
I need to reconstruct the bios on my board, based on another bios image form a real board - meaning a bios image containing MAC address, UUID and Serial number. A stock BIOS is not suffiecient, as it is impossible to discover where the MAC, UUID and SerialNumber are stored. Tried with a similar board, but there are too much differences, and the stock BIOS is missing a lot of...11-17-2023, 10:56 AM -
Hello,
I'm requesting a full BIOS dump (including EC firmware) for an HP OMEN 17-an012nf laptop.
Details:
Model : HP OMEN 17-an012nf
Motherboard Part Number : DAG3BAMBAF0 REV : F
Serial Number (S/N) : 5CD7280D51
BIOS chip : Winbond W25Q64VSIQ
Programmer : EZP2023+
Issue : The motherboard is not powering on. Only the 5V rail is present. The 3.3V rail is missing because EN1 on the SY8286B remains stuck at 0V. This signal is driven directly by the EC/SIO. I replaced the 3.3V regulator and confirmed it's working.
I already...
Comment