Thread merged..next time look for a thread with the name and model, motherboard model of the laptop, and post there, if you can't find it, then make a new thread.
Read the post above yours and post 16, try to fix it yourself. If editing or using the script doesn`t work then clean the ME firmware.
-
Please help me repair my bios file, is not come up after power led blink white and orange and have try some file in the thread but not perfect enough some start after some time fan spin fast no image
some display it will show up ......"Security End Point" Please help me with perfect bios with no complain
In case u need my backup. He is it down attached with info
HP Elitebook 840 G6
Board Number :6050A3022501-MB-A01
S/N: 2TK9490LWFLeave a comment:
-
Try this patcher -> https://www.badcaps.net/forum/troubl...security-errorLeave a comment:
-
Hello, I have the same problem can someone please help
HP EliteBook 840 G6
SN: 5CG9463MW5Leave a comment:
-
-
Halo I have a Laptop that has a Endpoint Security Controller Problem.
Can it be removed?
HP 840 G6
SN: 5CG0278SL8
Leave a comment:
-
-
Hello smdflea
here the ec file for the endpoint error
5CG0338SS1Leave a comment:
-
hello
smdflea
i try the patcher white no luck
So i ask you guys
Regards chrisLeave a comment:
-
You still have an extra 1KB in your file, did you read this -> Your bios is 32,769KB and should be 32,768KB ,i suspect the extra code has been added because you chose an OTP chip, you should choose a non OTP chip then it won`t add any extra .
And did you try what peste linked to, the script patcher will patch it for you, if you follow the instructions.
https://www.badcaps.net/forum/troubl...26#post3589426 -
hello
i send the wrong file about the endpoint problem
sorry for that
here is the good file
5CG0338SS1Leave a comment:
-
-
-
Leave a comment:
-
Hi, I have a problem with my HP EliteDesk 705 G5 Small Form Factor computer on amd . Standard corrupted bios probably corrupted during the update. I have uploaded a clean dump from the manufacturer's website with the latest version but when I turn it on a message appears :
HP Endpoint Security Controller problem
there is a problem with the hp endpoint security controller on the unit
I tried restoring the bios security to factory defaults after the first switch-on because this helps with intel-based laptops. Here unfortunately this did not help. Does anyone have... -
Have a Samsung UN50NU7400 which shows a boot screen and a screen saver if left on long enough but no picture ?
Would a moving screen saver confirm that the panel is ok or it could still be a panel issue ? -
Hi,
I have a iphone XS that came in for a screen replacement, the screen was badly cracked, and inside missing scues, on the back of the screen still the blue protector, the screen was a LCD. So we replaced the screen and all good, installed the screen and we noticed that pressing the screen with a bit of force but not excessive, the phone dies. After plugging the charger it turns back on, but again if you press it it dies. I open the phone again, and I can't see anything major, with the phone open, if I press on the logic board, battery, charging board, or even putting pressure on... -
Notebook HP ProBook 450 G8
ProdID 2K8L1LT#AC8
Mother: DAX8QAMB8D0 REV D
The device had bootloop issues. I reprogrammed the EC BIOS and the main BIOS, extracted from an HP 440 G8 with the same motherboard, and I was able to start the device. However, every time I turn it on, I get the error 'There is a problem with the HP Endpoint Security Controller in the unit.' I tried disabling several security options in the BIOS, but the error still appears. Additionally, when I attempt to update the BIOS, both BIOS chips get corrupted again....03-10-2025, 07:12 AM -
Hi! Please help with Endpoint Security Controller Problem, sending old not working dumps. Thankyou
and there is no soud after flashing new bios, may be have some solutions?
ProdID: 4YD62AV
SN: 2TK9500V8X...
Leave a comment: