820-3476-A Pulled resistor R8312

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Sepulmac
    New Member
    • Dec 2018
    • 9
    • Spain

    #1

    820-3476-A Pulled resistor R8312

    Hello everybody.

    First comment that I am a computer technician, not an electronics specialist, but I do like it.

    I tell you, by accident I have pulled the resistor R8312 and the GND pad of a motherboard 820-3476-A, the line is called DP_INT_ML_N <0> and it goes to pin 15 of the J8300 connector.

    The screen works and I don't know if it can be without that resistance. I guess not, but ... is it possible?

    Thank you.
    Last edited by SMDFlea; 04-15-2021, 01:59 AM. Reason: added "820-3476-A" to thread title
  • mon2
    Badcaps Legend
    • Dec 2019
    • 14020
    • Canada

    #2
    Re: Pulled resistor R8312

    R8312 = 1Meg, 0201, 5% pull-down resistor (to ground).

    Recommend to place this part back on but is a very weak resistor value and you may be ok to work without it.
    Attached Files

    Comment

    • Sepulmac
      New Member
      • Dec 2018
      • 9
      • Spain

      #3
      Re: Pulled resistor R8312

      Thanks mon2, for now I will leave it without soldering.

      Comment

      Related Topics

      Collapse

      • jinu_j
        Dell 2209WA - power supply - Fusible Resistor replacement
        by jinu_j
        Hi

        I am trying to repair an ancient Dell 2209WA Monitor which suddenly shut off with a pop sound. On investigation found that one of the fusible resistors had blown. Further investigation identified multiple components as faulty because of which the fusible resistor blew. Please refer the attached circuit diagram showing the components that were found to be damaged.

        1. FR950 - blown fusible resistor - 0.2 Ohm 1W
        2. Q950 - shorted Q950 MOSFET - 650V 10A N Channel Mosfet
        3. R835 - Blown Resistor - 20KOhm SMD resistor
        4. D930 - Shorted Schottkey Diode...
        05-03-2025, 10:51 PM
      • mikey5791
        Need help to replace burned resistor in 350w atx psu
        by mikey5791
        Hi to all forum members,

        Got this faulty 350 watt atx psu dirt cheap from a local online seller as i am keen to use it as a learning tool to repair faulty power supply.
        The faulty part is quite obvious from the burn area near the 16pin KA7500 BD pwm. The fuse is still intact with good continuity.

        Upon power on ac, there is 5vdc standby power on cathode of diode D14 and about 10vdc on cathode of diode D13.(This should be the aux power to generate the 12v and 5v rail.)
        Initially i replace the two burned resistors near my marked red arrow to 200 ohm resistor...
        12-26-2024, 04:55 AM
      • MidnightRoller
        Can a resistor lose resistance after hot air?
        by MidnightRoller
        I am curious if a 0402 resistor could go from 43 ohm to 0. In electronics class and my experience a resistor can degrade and gain resistance all the way up to not being able to conduct at all. I have never heard of a resistor decreasing in resistance and becoming 0 ohm or a dead short… that's not the direction they fail… or so I thought.

        I was attempting to remove a wson8 chip on an iMac motherboard and it required a lot of heat, on one side of the chip were 3 0402 resistors that were very close. I popped the chip out unintentionally out of the tweezers and sent those resistors...
        02-02-2022, 11:46 PM
      • artvandalai
        What resistor ohm will work better to repair this waterpik?
        by artvandalai
        The resistor on this waterpik blew. I changed it with the a similar spec 47ohm 2 watt yageo resistor but it still keeps blowing the resistor. Checking with the multimeter the motor, capacitor, diodes, and thermal fuse all checked normal. Will a higher ohm resistor work better? What ohm resistor will work better to repair this waterpik? This video is showing the repair with a 56 ohm resistor https://www.youtube.com/watch?v=_J7_rV7ui1Y
        01-05-2025, 04:10 PM
      • Document Archive
        MEDION ERAZER Specialist P10 Notebook Specification for Upgrade or Repair
        by Document Archive
        This specification for the MEDION ERAZER Specialist P10 Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the Specialist P10 boardview and Specialist P10 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or...
        09-07-2024, 06:11 AM
      • Loading...
      • No more items.
      Working...