OptiPlex 5080 Small Form Factor Bios

[lzeta]

Hi, I need bios file for OptiPlex 5080 Small Form Factor

service tag JYL58B3

I don't have the original dump because I've erase the eeprom and the usb where I've saved original isn't working anymore. I'm trying to recover it.

[hoaca388]

Hi, I need bios file for OptiPlex 5080 Small Form Factor

service tag JYL58B3

I don't have the original dump because I've erase the eeprom and the usb where I've saved original isn't working anymore. I'm trying to recover it.

OptiPlex 5080 Small Form Factor

[lzeta]

OptiPlex 5080 Small Form Factor

Thank you so much, witch one I must flash? After flashing have I to insert the service tag in the appropriate section of the bios?

[hoaca388]

Thank you so much, witch one I must flash? After flashing have I to insert the service tag in the appropriate section of the bios?

Yes .

[lzeta]

OptiPlex 5080 Small Form Factor

Please can you help me? I've flashed the
bin "2 CombineBiosName1 v99.1.45.rar" on winbond W25Q256JV@SOIC16 but the PC doesn't start, no fan, no led nothing. Must I try to flash the other or this is a dual bios and I must flash also the other? I have not seen another eprom to flash, I've desoldered the W25Q256JV and then programmed it with TL866II Plus and all went ok, I've checked the soldering and is ok.

[lzeta]

Bump

I think I must merge the two bios files (first "name1" and second "name2") and then I must flah it on W25Q256JV. Is it right?

[hardware1]

Bump

I think I must merge the two bios files (first "name1" and second "name2") and then I must flah it on W25Q256JV. Is it right?

You have to try both files one by one, because you lost your original backup and we can't know which one is suitable for your device.

[SMDFlea]

You have to try both files one by one, because you lost your original backup and we can't know which one is suitable for your device.

Look at the xml file. Models are in order ModelName="OptiPlex 5080, OptiPlex 5080-China HDD Protection" .

CombineBiosName1 - OptiPlex 5080
CombineBiosName2 - OptiPlex 5080-China HDD Protection

[hardware1]

Look at the xml file. Models are in order ModelName="OptiPlex 5080, OptiPlex 5080-China HDD Protection" .

CombineBiosName1 - OptiPlex 5080
CombineBiosName2 - OptiPlex 5080-China HDD Protection

Thanks, I didn't notice that before. So the proper file should be CombineBIOSName1 in his case?
I tried to do that with a another device "Dell G15 5511", and the differences was just the Model Number (0x0A70, 0x0A71). In that case I can decide which one to use if I have the original backup, so I can extract the old BIOS region and compare it with the other 2 to see which one is most similar (only if I use the same version).

[lzeta]

Look at the xml file. Models are in order ModelName="OptiPlex 5080, OptiPlex 5080-China HDD Protection" .

CombineBiosName1 - OptiPlex 5080
CombineBiosName2 - OptiPlex 5080-China HDD Protection

Thank you so much, I've flashed the "CombineBiosName2 - OptiPlex 5080-China HDD Protection" using a sop16 dip8 adaptor instead of the sop16 dip16 and it starts. Afeter first boot I've typed the service tag in the appropriate section (showed automaticaly on boot) than restarted the system that booted in manifacture programming mode, pressing alt+F (how indicated on boot) it show a menù I had to choose between:
OptiPlex 5080
OptiPlex 5080-China HDD Protection
I selected the "OptiPlex 5080"
Than it started normaly and finally I've updated at last version.

I still have doubts that it could also be an adapter problem because in my opinion the PC should have started with both bins. But maybe I'm wrong.

[Guilherme Augusto]

Hi! I program the BIOS file and the desktop (OPTIPLEX 5080 SFF) turned on, but i can't set the service tag. Always when i press alt+F, goes straight to boot. When i try to set in BIOS setup, always when reboot, shows the same screen (MANUFACTURING MODE) and the error continue, saying that service tag is no set. What can i do?

[lzeta]

Hi! I program the BIOS file and the desktop (OPTIPLEX 5080 SFF) turned on, but i can't set the service tag. Always when i press alt+F, goes straight to boot. When i try to set in BIOS setup, always when reboot, shows the same screen (MANUFACTURING MODE) and the error continue, saying that service tag is no set. What can i do?

Have you tried to reset cmos? Have you tried to enter bios setup manually? At least you can try to reprogram rom. Normally at first boot it opens bios in the service tag screen.