Lenovo thinkcentre M70q Gen 2 Logo

[mtherana]

Can someone please help remove the Third party boot logo on the bios

Lenovo ThonkCentre Gen 2

Machine type: 11N0
SN: PC2GE7RJ

[fauzanmint]

Can someone please help remove the Third party boot logo on the bios

Lenovo ThonkCentre Gen 2

Machine type: 11N0
SN: PC2GE7RJ

Try this one

[mtherana]

Try this one

The machine doesn't even switch on with this File no even fan spin.

now even with the Original backup still bricked

[volinakis]

The machine doesn't even switch on with this File no even fan spin.

now even with the Original backup still bricked

it means your backup was corrupted. Usually, if you update bios it will pop up a window with a message about custom logo, if you wanna keep it or not.

[mtherana]

Try this one

it went dead after I used this file, are you sure its for the same model this is the motherboard P/N: IB5X0IL2 NM-D331

or maybe do you have EC file. please

[mtherana]

it means your backup was corrupted. Usually, if you update bios it will pop up a window with a message about custom logo, if you wanna keep it or not.

Is the no way to fix mine, its very strange I made 2 different backups but with both same results.

[volinakis]

Is the no way to fix mine, its very strange I made 2 different backups but with both same results.

well, put back original backup, check soldering and let it run for few minutes

[mtherana]

well, put back original backup, check soldering and let it run for few minutes

Hi I did all that, 15min no fan spin no led light, the chip is making contact on all 8 pins. and no other file available anywhere else for M70q Gen 2 HB560 NM-D331 except Vinafix

[SMDFlea]

Hi I did all that, 15min no fan spin no led light, the chip is making contact on all 8 pins. and no other file available anywhere else for M70q Gen 2 HB560 NM-D331 except Vinafix

Did you verify before and after. You have made bad backups before so whats the reason ? ,are you using a clip, is the USB cable ok - try another one. Do you have another programmer you can try etc

https://www.badcaps.net/forum/troubl...e2#post3323890
https://www.badcaps.net/forum/troubl...g9#post3273024

[mtherana]

Did you verify before and after. You have made bad backups before so whats the reason ? ,are you using a clip, is the USB cable ok - try another one. Do you have another programmer you can try etc

https://www.badcaps.net/forum/troubl...e2#post3323890
https://www.badcaps.net/forum/troubl...g9#post3273024

Hello Sir and thanks for the response

I was using the CLIP for backing up. that means the problem began with the Clip and from now I must use the SOP8 Socket

how can I verify after backing up? UEFITool and was showing the Intel image was showing 4 Regions

and how can I now fix the file on Post #1

thank once again I thought by making 2 backups using the clip i will be safe.


thank you.

[SMDFlea]

Your backup at post 1 does look corrupt, starting at 16D3D10 with repeated patterns and gibberish until a bit further on where it reads properly again. Its possible the corruption was already there but i`d put the blame on the clip.Only 1 byte needs to be corrupt for the bios not to work,and you wouldn`t see it by looking.
Verifying 2 of the same corrupt backups means the backups are the same,and still corrupt.

EDIT: It isn`t corrupt, having had a look at the bios update the weird code is the same . The ME firmware is corrupt though

[mtherana]

can you please help me fix .

[SMDFlea]

can you please help me fix .

Try this bios.

[SMDFlea]

Try this one

It won`t work with unconfigured firmware. Read the ME cleaning guides https://www.badcaps.net/forum/troubl...22#post1622422

[mtherana]

It won`t work with unconfigured firmware. Read the ME cleaning guides https://www.badcaps.net/forum/troubl...22#post1622422

Thank you SMD it now works but has SVP.

[SMDFlea]

Thank you SMD it now works but has SVP.

Post the EC chip part number, and look around the board for unsoldered JTAG ports

[mtherana]

Here are the part numbers I couldn't find any jtags and have also tried to clear CMOS jumper

[mtherana]

Try this bios.

another question is the SVP not stored in this Bin file ? since on the corrupted one on POST #1 I was able to change the settings and even disabled computrace. main issue I couldn't get around was to remove the Logo since the official firmware only gave an option update the firmware.

thank you.

[SMDFlea]

another question is the SVP not stored in this Bin file ? since on the corrupted one on POST #1 I was able to change the settings and even disabled computrace. main issue I couldn't get around was to remove the Logo since the official firmware only gave an option update the firmware.
thank you.

Havn`t had time to look.

[mtherana]

Try this bios.

Can someone please Help remove SVP on this File Please..

[SMDFlea]

Are you sure you put the jumper on the right pins https://www.youtube.com/watch?v=2tyjdimosuk .