B560M D3H help identify component

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • sellit
    Senior Member
    • Jun 2017
    • 104
    • Latvia

    #1

    B560M D3H help identify component

    Hello. I Got B560M D3H rev. 1.0 Turns on no picture, CPU stays cold.
    After power button pressed Resistor arrays near ATX power connector gets hot. Got 11.93V on ATX side of resistors. After resistor array 0V.
    Injected 12V after resistor array, component with marking "11M36" gets hot. Please help identify it.
    Looked at B550M DS3H Motherboard what got the same resistor arrays, there that component marking was "11N01"
    Attached Files
  • anikin73
    Senior Member
    • Mar 2022
    • 112
    • singapore

    #2
    Re: B560M D3H help identify component

    I am not sure why you get to that chip. You should start by measuring all the main voltages to see whether it appear.

    Comment

    • nubie
      Senior Member
      • May 2010
      • 63

      #3
      Re: B560M D3H help identify component

      I have similar symptoms on a Z490 Gigabyte:

      CPU Cold
      MOSFETS cold

      CPU POST debug LED lit up*

      This component 11M36 is the hottest thing on the board by a large margin when I look at it with a FLIR ONE thermal camera.

      Not sure what the component does or where it goes in the circuit


      *Tested working Celeron chip, immaculate socket.
      Attached Files
      Last edited by nubie; 09-13-2023, 10:10 PM.

      Comment

      Related Topics

      Collapse

      • gica69
        Need help to identify and to locate a 0.33 ohms fusible resistor for power supply
        by gica69
        I have a quad charger that is split into 4 separate sections and one section doesn’t charge anymore. I have located what I think is a thermistor and on the shrink tube it says 125 degrees C. I cut the shrink tube and it's a 33 ohms resistor. It measures a little less than 1/2 inch in length. I am including pictures of it. Please help me identify it. So, it should test at 0.4ohms and probably go up in resistance with the rise in temp. On the board it clearly says R for resistor. But it has to be a special one.
        Resistor shows orange range silver gold and green lines.
        Thanks in adv...
        07-21-2025, 09:49 PM
      • DynaxSC
        Weired MSI B560M PRO (MS-7D20) - not starting with 11-th gen. CPU, 10-th gen. OK
        by DynaxSC
        Hi,

        I have a very weired problem with MSI B560M PRO (MS-7D20), board is upgraded to the latest BIOS version v1.9.

        The board is normally starting with 10-th gen. CPU, ie. Intel Comet Lake i5-10600K and Celeron G5905.

        However if I install a 11-th gen. Rocket Lake i5-11600K the board powers up, but is immediately stuck on CPU LED, not progressing further. Debug card shows FF, and after restart with long short of Power Button: FE, which is as usually of no help (Reserved for future AMI error codes).

        According to MSI compatibility site the board supports...
        11-04-2024, 04:04 PM
      • jinu_j
        Dell 2209WA - power supply - Fusible Resistor replacement
        by jinu_j
        Hi

        I am trying to repair an ancient Dell 2209WA Monitor which suddenly shut off with a pop sound. On investigation found that one of the fusible resistors had blown. Further investigation identified multiple components as faulty because of which the fusible resistor blew. Please refer the attached circuit diagram showing the components that were found to be damaged.

        1. FR950 - blown fusible resistor - 0.2 Ohm 1W
        2. Q950 - shorted Q950 MOSFET - 650V 10A N Channel Mosfet
        3. R835 - Blown Resistor - 20KOhm SMD resistor
        4. D930 - Shorted Schottkey Diode...
        05-03-2025, 10:51 PM
      • mikey5791
        Need help to replace burned resistor in 350w atx psu
        by mikey5791
        Hi to all forum members,

        Got this faulty 350 watt atx psu dirt cheap from a local online seller as i am keen to use it as a learning tool to repair faulty power supply.
        The faulty part is quite obvious from the burn area near the 16pin KA7500 BD pwm. The fuse is still intact with good continuity.

        Upon power on ac, there is 5vdc standby power on cathode of diode D14 and about 10vdc on cathode of diode D13.(This should be the aux power to generate the 12v and 5v rail.)
        Initially i replace the two burned resistors near my marked red arrow to 200 ohm resistor...
        12-26-2024, 04:55 AM
      • MidnightRoller
        Can a resistor lose resistance after hot air?
        by MidnightRoller
        I am curious if a 0402 resistor could go from 43 ohm to 0. In electronics class and my experience a resistor can degrade and gain resistance all the way up to not being able to conduct at all. I have never heard of a resistor decreasing in resistance and becoming 0 ohm or a dead short… that's not the direction they fail… or so I thought.

        I was attempting to remove a wson8 chip on an iMac motherboard and it required a lot of heat, on one side of the chip were 3 0402 resistors that were very close. I popped the chip out unintentionally out of the tweezers and sent those resistors...
        02-02-2022, 11:46 PM
      • Loading...
      • No more items.
      Working...