MSI GTX1070 not recognized on H110 Board, Z490 OK

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • DynaxSC
    Badcaps Veteran
    • Apr 2021
    • 455
    • Poland

    #1

    MSI GTX1070 not recognized on H110 Board, Z490 OK

    Hi,

    I have an MSI GTX1070 GAMING X card, which I buyed and repaired. It got wet with something and corroded slightly in an limited area. There were a few resistors and caps around the VRM Controller, which were corroded, and had to be replaced, traces to be tinned, corrosion to be removed. Sof far so good, the card is recognized in BIOS and works perfectly on a modern Z490 board. But when I put the card into a H110 board (tried different) then it is not recognized by the BIOS, and does not show up neither in Windows nor in Mods. Tried all possible Bios settings, updated mobo Bios, to no avail. Very strange

    The area where the board has correded due to some electrolysis effect is quite limited (ca 4 X 6 cm) near the 1V8 buck controller and far away from the PCI connector, GPU, and all the PCI logic. Etherything only on the top side no more then 1-5 cm from the edge farest away from the VGA connectors. It may be possible that I have not identified some corroded resistor (no conduction possible as resistor pads were totally ethed on the other ones) that give some signal necessary to detect the card on older boards.

    I have no clue what could be the reason. Any hints appreciated.
    Last edited by DynaxSC; 01-26-2022, 04:59 PM.
  • DrasticRepairs
    Member
    • May 2021
    • 23
    • United States

    #2
    Re: MSI GTX1070 not recognized on H110 Board, Z490 OK

    Could be pcie capacitors. Not sure what else.

    Comment

    • Agent24
      I see dead caps
      • Oct 2007
      • 4951
      • New Zealand

      #3
      Re: MSI GTX1070 not recognized on H110 Board, Z490 OK

      Could it be that the card is fine but just incompatible with the other board?
      "Tantalum for the brave, Solid Aluminium for the wise, Wet Electrolytic for the adventurous"
      -David VanHorn

      Comment

      Related Topics

      Collapse

      • Tynan Dill
        Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
        by Tynan Dill
        I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

        Upon bringing it home and plugging it up, it showed a standby light.

        I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

        The screen seems to blackout and stay black, but with a flashlight I can see the display.

        With my Playstation 4 connected via HDMI, and running a game I can hear sound.

        Assuming...
        11-22-2024, 01:46 PM
      • m1ch43lzm
        HP Pavilion 15-eh Board DAG7HAMB8F0 - CPU throttling to 0.4GHz (PROCHOT_EXT) and black screen
        by m1ch43lzm
        Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
        Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic...
        05-12-2025, 08:37 PM
      • DynaxSC
        ASUS STRIX Z490-F GAMING - No POST, stubborn board
        by DynaxSC
        Hi,

        I have this very stubborn ASUS mobo on the bench, and I already face the wall with it. It just refuses to POST, although everything seems to be OK.

        The situation looks like this:

        After connecting the board to the power supply on Nuvoton (SLP_S3#, pin 64), the Low signal (50 ohm resistance) appears immediately. PWRNTN# signal goes through Nuvoton to the chipset (confirmed after removing the chipset). The following conditions are then met for the chipset to generate the SLP_S3# signal:

        1. RTC oscillates normally (32.768KHz).
        ...
        07-08-2022, 05:45 AM
      • howardc64
        TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
        by howardc64
        All left and right refers to looking from rear of TV (or looking from front with TV upside down)
        • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
        • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
        ...
        Yesterday, 05:17 PM
      • Junior††
        PS5 Disc Not Supported/ Disc Not Recognized Board Num: EDM-020
        by Junior††


        Good Afternoon fellas,

        Issue:
        Disc is showing as not supported when a disc is put in.

        Here's what I've done, you can skip this if you just wanna know the question:
        - replaced with a disc drive from a donor ps5 (honestly questionable if this is known to work)
        - reflowed the disc drive connector
        -reflowed the chip in question (shown on image)
        - I will say this console was very dusty so it's conceivable that it got so hot that it made the chip joints cold and potentially other things on the board

        Question:
        I...
        02-19-2025, 12:48 PM
      • Loading...
      • No more items.
      Working...