IPISB-AG Rev 1.03 Motherbaod fault

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • emotechsys
    New Member
    • Oct 2021
    • 5
    • Spain
    #1

    IPISB-AG Rev 1.03 Motherbaod fault

    I have this motherboard. When I connect to current, the current led switches on and slowly goes off. If I disconnect and wait a little, it will do same. Or if I breach the bios battery and connect to current, it will switch on and goes off slowly.
    Can anyone give me helping hand? The Board name is IPISB-AG Rev 1.03
    Attached Files
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • PanicMechanic
      Extech EX330 multimeter current range offset fault
      by PanicMechanic
      My multimeter has developed this fault, a few months ago. I tried to fix it, but had no success.

      The fault is that on the current ranges it never shows 0. Does not matter if the probes are open or shorted.
      As you can see from the pics, the offser is the same (just multiplied for other rages):

      -4.9 uA
      -0.49 mA
      -0.49 A

      I don't know what exactlly caused the fault.

      The meter had a battery leak before I noticed the fault, but I am not sure if the fault was present before that happened. I just did not noticed. The battery leaked...
      05-11-2021, 11:13 PM
    • sam_sam_sam
      Is there any high current pouch battery that are size 60mmX80mm maximum thickness 21mm for a battery operated tab welder
      by sam_sam_sam
      I have a battery operated tab welder and the battery does not have enough current for the battery tab welder because after about 30 welded it does not have the same current output it voltage has gone down by at least 0.500 volts or maybe a more than that

      I can fit 21700 battery cells in the enclosure it is very tight fit for four of them that are 35 amp high current capacity 35X4=140 high current output this should work a lot better than what is installed right now

      I tested the battery cells there are installed right now and they are testing good with no issues that I...
      02-04-2025, 08:08 PM
    • DynaxSC
      Extreme High Current & Low Voltage Short Killer ??
      by DynaxSC
      Hi Folks

      I'm looking for a extreme high current short killer solution for a reasonable cost.

      I have an LGA1700 motherboard (ASUS PRIME Z790-P WiFi) where I exchanged the LGA socket already 3 times, and every time after the socket exchange I get a short of power supply lines VCORE (V variable) and VCCIN_AUX (1.8V).
      After taking off the socket, the shorts dissappear again.
      The soldermask on the socket is already partially demaged from the heat, so I have reconstructed the soldermask by manually painting the missing soldermask parts with a very small top of a...
      10-15-2024, 10:13 AM
    • sam_sam_sam
      Adjustable Boost Power Supply DC-DC Constant Voltage Current Charging Module
      by sam_sam_sam
      I want to know if I could hook up a solar panels to this boost converter would I have any issues doing and I would have issues what would they be

      Adjustable Boost Power Supply DC-DC Constant Voltage Current Charging Module

      https://www.ebay.com/itm/116497313155?var=416785404161


      Here are some of the description from the eBay seller

      The main parameters:
      1. Product name: High-power non-isolated DC boost module power supply.
      2. Product model: 100A2000W.
      3. Input voltage: DC12V-60V.
      4. Input current: 100A (maximum)....
      05-18-2025, 09:45 AM
    • Document Archive
      Surface Mount Fuses Fundamentals Datasheet
      by Document Archive
      TE Circuit Protection offers the widest selection of surface-mount fuses available for addressing a broad range of overcurrent protection applications. Helping to prevent costly damage and promote a safe environment for electronic and electrical equipment, our single-use chip fuses provide performance stability to support applications with current ratings from .5A up to 20A.

      TE Circuit Protection also offers the telecom FT600 fuse for telecommunications applications. This telecom fuse helps comply with North American overcurrent protection requirements, including Telcordia, GR-1089,...
      10-07-2024, 06:07 AM
    • Loading...
    • No more items.
    Working...