Wi-fi is lossy for some but not others

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • japlytic
    Badcaps Legend
    • Oct 2005
    • 2085
    • Australia

    #21
    Re: Wi-fi is lossy for some but not others

    If only there were wireless routers which have separate G and N radios, with the N radio locking out all but N clients.
    My first choice in quality Japanese electrolytics is Nippon Chemi-Con, which has been in business since 1931... the quality of electronics is dependent on the quality of the electrolytics.

    Comment

    • Danblade
      New Member
      • Mar 2012
      • 3
      • USA

      #22
      Re: Wi-fi is lossy for some but not others

      I like to use Asus brand routers. I then install dd-wrt and usually don't have any problem.

      Comment

      • japlytic
        Badcaps Legend
        • Oct 2005
        • 2085
        • Australia

        #23
        Re: Wi-fi is lossy for some but not others

        Check out http://www.aaacom.com.au/residential-services/
        They say the biggest fraud is wireless (and forgot to add powerline) networking speeds - and I certainly agree!
        My first choice in quality Japanese electrolytics is Nippon Chemi-Con, which has been in business since 1931... the quality of electronics is dependent on the quality of the electrolytics.

        Comment

        Related Topics

        Collapse

        • bulkchart32
          i cannot get rid of the interference in the video on this 1.1v and i have tried everything!
          by bulkchart32
          i recapped the entire foxlink psu with rubycon caps of the exact uf needed. i also purchased a delta psu to see if the different brand would change anything and it did not. i recapped the entire motherboard except for about 5 of the 22uf caps. i used rubycon on everything except the five in front of the processors. i used 5 nichicon polymer caps there. i soldered a wire to each screw hole of the psu and soldered one wire to the metal outer shell and one to a screw hole on the motherboard(to make sure it was all grounded well). i also recently tried disconnecting the power cables from the dvd drive...
          Today, 02:37 AM
        • Zelek11
          Panasonic Plasma screen interference on left half of screen
          by Zelek11
          My Panasonic Plasma model P55VT50 has started displaying "interference" on just the left half of the screen only (left when facing the screen). Sometimes it's concentrated in about the first 30 seconds after startup, then disappears. Other times it's fine at startup and then randomly does it later on. When it flashes the interference it's very quick and doesn't stay on the screen unless it flashes repeatedly in a row.



          This image is a screen shot from a video I took. This is an example of the interference at its worst. Often the interference is much smaller...
          10-14-2022, 04:54 PM
        • novator2007
          Help with finding ThinkPad T460 JTAG Points
          by novator2007
          Hello All,

          I got a T460 with issue - No picture - Fan on full Speed and no Power LED Light.
          Bios already reflashed
          All standard voltage is present. CPU on emergeny(?) mode - max 30 c Grad.


          By Schematc & BRD View I have found few Debug/Jtag points.
          Just not sure which one is correct,
          1.There is some(under lack) Test points near CPU - Schematic Page 6
          2. J9 26p place for connector - Present: PCH_TMS/TDI/TDO/TCK/RSMRST
          3. J8 26p place for Connector - XDP_TMS/TDI/TDO/TCK/RSMRST

          I trying to find a correct...
          08-02-2022, 07:49 AM
        • lmcancu
          LED Strip test points and testing?
          by lmcancu
          Hi is there a guide in this forum on how to test the LED backlight TV strips? I purchased an LED tester on amazon, but I am a bit confused on the test points and how to test the individual LEDs? I took apart a RCA 43" TV Rlded4331b. Please see attached pictures. I understand that all the LEDs are in series, but on these strips I don't see any individual test points for each LED? Any tips or guides?
          Thanks in advance...
          03-20-2023, 07:52 AM
        • migax miranda
          hp 15s-eq0012np contact points on the "type C" charger input were torn off
          by migax miranda
          Hello, a "hp 15s-eq0012np" arrived to me, the only problem with it is that the contact points on the "type C" charger input were torn off. Can anyone tell me what the purpose of each "leg" of the connector is? Which ones are really necessary for it to charge the battery and turn on?
          10-13-2024, 10:03 AM
        • Loading...
        • No more items.
        Working...