Optiquest Q9 no power

[PincushionMan]

Re: Optiquest Q9 no power

Here's what I ordered. Panasonic FC series all (I saw that the CapXon are supposed to be comparable ESR-wise to these). Hope I am close.

1. 10 10 0 0 P10316-ND EEU-FC1H100L DD-C824 0.13700 $1.37
2. 10 10 0 0 P10326-ND EEU-FC1H221S DD-C904 0.54500 $5.45
3. 10 10 0 0 P11261-ND EEU-FC1H561 DD-C802 0.96600 $9.66
4. 10 10 0 0 P11203-ND EEU-FC1C102S DD-C829 0.54600 $5.46
5. 10 10 0 0 P10249-ND EEU-FC1C681L DD-C819 0.32600 $3.26
   

Also, still working on the pictures. My camera made them too big for the 2000 x 2000 px limit, so I'll have to scale them a bit. I could've sworn I set the camera to 1024x768. Go figure.

[EGuevarae]

Re: Optiquest Q9 no power

I have a pair of Optiquest Q9 (Actually Q9B-2, I think the B means refurbished). Both purchased in the same time frame (from CDW), both died after 13 to 16 months of very light use.

When I pulled the power (inverter?) board from both of these units, I see the same thing, a single leaky CapXon capacitor. I'm fairly certain the fuse is blown, also. The board is labeled as follows:
2006/10/20
PI-SB03
REV
Digital Decade Ltd.
P/N: BLM1700P60210

Input:
100-240 Vac @ 60 Hz
Output:
24Vdc, 0.05A (optional)
5Vdc, 2.5A
-8Vdc, 0.1A (optional)
Caution: For continous protection against risk of fire replace only with same type and rating fuse.

Seems to be a T 3.15A/250V black/radial type fuse with the word bel in the center.

I have a list of all the CapXon capacitors on the board (all are KF 105C date code P640 = 2006, Week 40):


_100uF 400V C809 ~18mm x 35mm (will leave alone)
__10uF _50V C824 _~5mm x 10mm
_220uF _50V C904 ~10mm x 15mm (G sticker on Vent)
_470uF _50V C804 ~10mm x 20mm
1000uF _16V C829 ~10mm x 19mm (leaking goo)
_680uF _16V C819 ~10mm x 15mm


Pics to follow.

Replace them all, except the big one if you don't want to do it.

[PincushionMan]

I have a pair of Optiquest Q9 (Actually Q9B-2, I think the B means refurbished). Both purchased in the same time frame (from CDW), both died after 13 to 16 months of very light use.

When I pulled the power (inverter?) board from both of these units, I see the same thing, a single leaky CapXon capacitor. I'm fairly certain the fuse is blown, also. The board is labeled as follows:
2006/10/20
PI-SB03
REV
Digital Decade Ltd.
P/N: BLM1700P60210

Input:
100-240 Vac @ 60 Hz
Output:
24Vdc, 0.05A (optional)
5Vdc, 2.5A
-8Vdc, 0.1A (optional)
Caution: For continous protection against risk of fire replace only with same type and rating fuse.

Seems to be a T 3.15A/250V black/radial type fuse with the word bel in the center.

I have a list of all the CapXon capacitors on the board (all are KF 105C date code P640 = 2006, Week 40):


_100uF 400V C809 ~18mm x 35mm (will leave alone)
__10uF _50V C824 _~5mm x 10mm
_220uF _50V C904 ~10mm x 15mm (G sticker on Vent)
_470uF _50V C804 ~10mm x 20mm
1000uF _16V C829 ~10mm x 19mm (leaking goo)
_680uF _16V C819 ~10mm x 15mm


Pics to follow.