Hannsg HH251dpb

nbdy

Senior Member

Join Date: Aug 2015

Posts: 162

Country: Croatia
#1

Hannsg HH251dpb

11-07-2018, 12:48 AM

Hi,

Have a Hannsg HH251dpb with a white screen right after pluging in power ...

Only the power button turn the monitor on and off,no other button reaction ...

Read about some test mode (could it be?) ...

All caps on PSU look ok ...

The main board looks ok 2 ...

Any knowledge where to look further ...

thx
Tags: None
nbdy

Senior Member

Join Date: Aug 2015

Posts: 162

Country: Croatia
#2

11-08-2018, 12:25 PM

Re: Hannsg HH251dpb

Managed to measure the voltages ...

have 5V,12V,PSON,O/F,ADJ - all present

the board is FSP060-2PI11
Comment

Previous template Next

ACER Spin 5 SP514-51N after usb-c controller ic change no reaction to charger - must it be programmed first?

by ktmmotocross

Hello.
Have this ACER Spin 5 SP514-51N that have only 5V on usb-c charging ports and usb-c comtroller CYPD5225-96BZXI heats up. so i order new controller and replace it. now u have no reaction to charger. must be this ic programmed first and if yes than how...
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
06-17-2025, 12:11 AM
ASRock B450 Steel Legend - no reaction to power button

by karlp028

I've got an ASRock B450 Steel Legend that I'm trying to diagnose for no reaction to the power button.

The SIO receives the PWRBTN# signal and sends PSOUT#, but the CPU doesn't return SLP_S3# so nothing further happens. I have been looking around the board trying to figure out why and I happened to touch the STEP-DOWN CONVERTER NB685GQ-Z (UP10 in photo) which was VERY hot (like burn your finger). This seems to provide VDDP_S5, and indirectly, VDDCR_SOC_S5, which the CPU needs in order to handle the startup signals.

The VCC voltage powering the converter does not look right....

1 Photo
- Channel: Troubleshooting Desktop Motherboards, Graphics Cards, and PC Peripherals
02-09-2025, 03:52 PM
MSI PRO Z690-A WIFI DDR4 no reaction to the power button

by karlp028

I've got an MSI PRO Z690-A WIFI DDR4 that has no reaction to the power button. I have been doing some exploration to try to determine what is wrong with it.

The front panel PSIN# pin has 3.3V on it, so i started tracing from there to the SIO, which is a Nuvoton NCT6687D. Connectivity from the front panel PSIN# to pin 61 on the SIO is good and when I short PSIN# to GND then pin 61 goes low as it should.

However, I noticed that SIO pin 61 PSOUT# was already low, even before I activated PSIN#. Does this mean the SIO chip is hosed or could there be another explanation? I'm...
- Channel: Troubleshooting Desktop Motherboards, Graphics Cards, and PC Peripherals
11-29-2024, 07:04 PM
HANNSG Hi221 -- 2 secs to black feat. CCFL flicker & "burn" marks on power board

by ttmi100x

Greetings everyone,

I have a HANNSG Hi221 monitor that exhibits two seconds to black issues (backlight goes off, display is still on as confirmed by shining a flashlight on it) with some additional oddities...

The monitor failed on me with a standard "2 seconds to black" some time ago prompting me to initially replace most of the electrolytic capacitors (some of them were bulging/leaking).
Things kinda sorta worked for a night, then the problem returned along with some flickering and "buzzing" noises.

Upon closer inspection...

6 Photos
- Channel: Troubleshooting Computer Displays
07-31-2024, 06:36 PM
T480 with GeForce MX150 - not charging, no reaction to power button

by sant1

Hello,

MEC1653-BA1 pulled VCC3M down to 60ohm, replaced it, programmed with vertyanov, no reaction to on/off button and not charging now.
Noticed that VSYS_OUT is 9.18V, had a opportunity to compare on UMA T480, it was 10.2V, no ideas if DGPU T480 should have same VSYS_OUT.
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
04-02-2024, 07:34 AM
Loading...
No more items.

Hannsg HH251dpb

Hannsg HH251dpb

Comment

Related Topics