HP LCD with bad caps

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • dood
    Deputy dood
    • Mar 2004
    • 2462
    • USA
    #1

    HP LCD with bad caps

    Unfortunately, I didn't get the model off this monitor before I returned it. Just a basic older 15" LCD. Would not turn on or even flash the power light when it came to me.








    Recapped with panny's


    Replaced all but the main cap (it was already a nichi) just for good measure.


    I should probably organize my desk.


    Lookin' good, now.
    Ludicrous gibs!

    Tags: None
    • ant3202
      Badcaps Veteran
      • Jun 2006
      • 275
      • Singapore
      #2
      Re: HP LCD with bad caps

      good work!

      btw panny caps u r using is FM series?

        Comment

        • dood
          Deputy dood
          • Mar 2004
          • 2462
          • USA
          #3
          Re: HP LCD with bad caps

          Yep, panny FMs
          Ludicrous gibs!

            Comment

            • ant3202
              Badcaps Veteran
              • Jun 2006
              • 275
              • Singapore
              #4
              Re: HP LCD with bad caps

              i see thanks

                Comment

                • Krankshaft
                  Badcaps Legend
                  • Jan 2007
                  • 2328
                  • USA
                  #5
                  Re: HP LCD with bad caps

                  I use FCs on my inverter recaps they work well too.

                  This is why I say that Crapxon caps are dodgy at best they are like Teapos sometimes they work great and sometimes they fail.
                  Elements of the past and the future combining to make something not quite as good as either.

                    Comment

                    • dood
                      Deputy dood
                      • Mar 2004
                      • 2462
                      • USA
                      #6
                      Re: HP LCD with bad caps

                      Capxon seem okay as long as they're adequately cooled. In this LCD screen there would obviously be a lot of heat buildup.
                      Ludicrous gibs!

                        Comment

                        Previous template Next

                        Related Topics

                        Collapse
                        • momaka
                          Seasonic B12 BC-550 – barely 2 years old and with BAD CAPS already!
                          by momaka
                          I know I've been a little scarce lately (like the last 2-3 years), but I'm still here and still doing my thing with fixing PSUs.

                          For today's considerations, I have a Seasonic B12 BC-550 [A551bcafh] 550 Watt ATX power supply for you (click on links for full size images).

                          https://www.badcaps.net/filedata/fetch?id=3591771


                          https://www.badcaps.net/filedata/fetch?id=3591772

                          It's a modern ATX unit with fixed (non-modular) cables and an 80-plus bronze certificate. Here's the label:

                          https://www.badcaps.net/filedata/fetch?id=359177...
                          03-12-2025, 03:42 PM
                        • eryjus
                          Heathkit IO-4205 Power Supply Caps
                          by eryjus
                          Hello,

                          First, I am a complete noob with high voltage stuff. I'm learning, but I need help by someone looking over my shoulder.

                          I recently came into posession of a Heathkit IO-4205 5MHz Dual Trace Oscilloscope. The documentation is copyright 1978. I'm told it works.

                          I opened it up to check the caps before I applied power, and found the following black caps and wanted to know what they were. They are on the power supply board. I was able to read the name and model and came up with, "Nytronics 162J-1, 0.1uF, 20% tolerance, 2000VDC."
                          ...
                          05-10-2023, 11:21 AM
                        • Paxman_Swede
                          Identifying caps on an old Zoom 9000
                          by Paxman_Swede
                          Hello!

                          I have two projects on my work bench. One is a friends dead JBL Xtreme speaker with a blown voltage regulator and corresponding bulged and shorted cap. That cap has clear markings so I know what replacement I need for it.

                          The other project however is a whole different deal. It's a Zoom 9000 guitar effect from the 90th that has developed a devil hound howl when there is no input from the guitar. I'm guessing caps problem. So, since I don't really use this effect anymore I thought it would be a perfect project to learn on.

                          I have studied the board and...
                          01-14-2025, 09:51 AM
                        • captain150
                          Help with switching power supply caps
                          by captain150
                          I'm trying to repair two old VCRs, they both have bad caps. One has leaky ones, the other would barely run until I subbed in some caps from another power supply I had laying around (though they are the wrong values). This vcr works for an hour or two, but then the power supply starts whining and the picture gets lines in it. I didn't replace all the secondary caps, so another voltage might still be problematic, or the values I used are too far off.
                          I've been on mouser and digikey but the options are a bit overwhelming. I just need some new ones that will work. They don't need to be top quality,...
                          03-16-2025, 07:34 PM
                        • Foetuss
                          Gigabyte GA-6OXT :: caps question
                          by Foetuss
                          Good evening

                          I recently aquired a rev 1.1 Gigabyte 60XT, and was suprised of the amount of leaking caps for a motherboard of the P3 era. Especially the way the 330µf caps seems like the housing discolored even.
                          Now, there are some 3300µF 6.3V KZG series around the CPU. Would it be OK to replace them with something like EEUFR1A332 ? (Panasonic FR 3300µF 10V). Or was this board designed around very low ESR caps?

                          But I was also suprised about the bigger boys, which are 330µF 25V.
                          Could it be they used 25V caps because they were cheaper / available at that time?...
                          02-11-2025, 12:22 PM
                        • Loading...
                        • No more items.
                        Working...