VP201b Viewsonic

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • eswallie
    New Member
    • May 2011
    • 4
    #1

    VP201b Viewsonic

    I bought 4 Viewsonic vp201b's about 3 years ago and all four went out within the same month about 2 years later. I sent all 4 off for repair at $100.00 each plus 25.00 shipping each way. Now they have all gone out again and I am not sending them back again.

    To make a long story short, I can't even get the dam cover off to get to the electronics. I found the four screws (on each corner) but what is next?
    skeeedaddy
    Tags: None
    • retiredcaps
      Badcaps Legend
      • Apr 2010
      • 9271
      #2
      Re: VP201b Viewsonic

      Originally posted by eswallie
      I found the four screws (on each corner) but what is next?
      Pry it apart like

      http://www.youtube.com/watch?v=Ul5LhuCT1y8
      --- begin sig file ---

      If you are new to this forum, we can help a lot more if you please post clear focused pictures (max resolution 2000x2000 and 2MB) of your boards using the manage attachments button so they are hosted here. Information and picture clarity compositions should look like this post.

      We respectfully ask that you make some time and effort to read some of the guides available for basic troubleshooting. After you have read through them, then ask clarification questions or report your findings.

      Please do not post inline and offsite as they slow down the loading of pages.

      --- end sig file ---

        Comment

        • eswallie
          New Member
          • May 2011
          • 4
          #3
          Re: VP201b Viewsonic

          OK, I got it apart. The trick is two screws behind the stand. Now I need a power supply ADP-60BF A for the VP201b moniter. I found a place in China but they are all out. Now what?
          Ernie

            Comment

            • sabre504
              Badcaps Veteran
              • May 2010
              • 449
              • United Kingdom
              #4
              Re: VP201b Viewsonic

              Hi have you tried this site

              http://www.mylcdboard.com/2010_11/ZD100205.html

                Comment

                • Mad_Professor
                  A Mech Warrior
                  • Feb 2011
                  • 1587
                  #5
                  Re: VP201b Viewsonic

                  Are you sure it's not bad caps?

                  Take some pics, maybe we can help.
                  List the brand, series, capacitance and volts.

                    Comment

                    Previous template Next

                    Related Topics

                    Collapse
                    • lostone
                      Looking for help with a Viewsonic VP230mb where the backlight comes on only momentarily
                      by lostone
                      Hello, I came here after finding some similar questions asked on other monitors and hope someone here can help me get an ancient Viewsonic VP230mp (23" 4:3 LCD) back to working condition.

                      First a little background, I have a background in computer and electrical engineering, and I'm smart enough to know I know nothing about LCD displays and how they work. For this topic I'm as green as they come.
                      When the display is turned on the viewsonic logo displays in the uppper left for 2 seconds then the screen goes black, the power LED is green (on) and when a computer is connected...
                      05-19-2024, 11:40 AM
                    • howardc64
                      A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
                      by howardc64
                      Problem

                      This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
                      08-04-2024, 10:36 PM
                    • StefanNg
                      Viewsonic VX2718-PC-mhd SG2701B01-8
                      by StefanNg
                      Hi, Badcaps.

                      I am troubleshooting a monitor
                      Viewsonic VX2718-PC-mhd.
                      Panel model SG2701BSG2701-8
                      Symptoms is no image.

                      This panel has 2 panel board connected by a U-ribbon.
                      When I disconnected the ribbon, I get a perfect half screen image.
                      I took some test point voltage, when ribbon disconnected.
                      HVAA 8.38v
                      FVDD12 1.21v
                      FDD33 3.3v
                      VIN 11.79v
                      VAA 16.85v
                      VGHF 30.16v
                      VGL -8.02v
                      CK1_I ~ CK8_I 1.403v
                      CK1_L ~ CK8_L 8.26v

                      When I connect both panel board
                      HVAA, VGHF, and CKx_L...
                      3 Photos
                      05-17-2025, 01:43 AM
                    • Fagauthier
                      Viewsonic power supply model #EADP-64BF B Need circuit diagram…
                      by Fagauthier
                      I have à defective Viewsonic monitor. I can't find a circuit diagram for it' power supply.
                      Model #EADP-64BF B
                      The user manual have all diagram except for the power supply. I would appreciate help to find the circuit diagram, thanks...
                      07-08-2023, 08:02 PM
                    • Widget
                      Anyone repaired Ionmax ION390? I have extra screws :(
                      by Widget
                      Hi all,

                      Re-assembling a Ionmax ION390 air purifier after removing the top LCD control panel, I seem to have 2 extra screws that I, for the life of me, cannot see where they go. I've taken a couple of pictures, buuuuut there's always that one picture you need, but you didn't take :/.

                      I know it's a long-shot but has anyone repaired this before would have an idea?...
                      04-26-2023, 11:15 PM
                    • Loading...
                    • No more items.
                    Working...