Elan z660/661 amplifier

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • linksys1127
    Senior Member
    • Sep 2016
    • 121
    • United States
    #1

    Elan z660/661 amplifier

    Does anyone have a service manual or any schematics on this? I found a bad ceramic cap but unable to get any info off of it for replacement. It's smoked! Replaced other faulty components in the circuit just need specifics for for c75 on the power board.
    Thanks, Kevin
    Tags: None
    • petehall347
      Badcaps Legend
      • Jan 2015
      • 4451
      • United Kingdom
      #2
      Re: Elan z660/661 amplifier

      what does it connect to in the circuit ? example parallel with diode .

        Comment

        • linksys1127
          Senior Member
          • Sep 2016
          • 121
          • United States
          #3
          Re: Elan z660/661 amplifier

          Installed on the output side of a 12volt positive voltage regulator. I'll send a picture of it. The cap next to it has 104 on it which I believe should be a .1uf.

            Comment

            • linksys1127
              Senior Member
              • Sep 2016
              • 121
              • United States
              #4
              Re: Elan z660/661 amplifier

              Attached Files

              if you find these attachements useful please consider making a small donation to the site

                Comment

                • R_J
                  Badcaps Legend
                  • Jun 2012
                  • 9634
                  • Canada
                  #5
                  Re: Elan z660/661 amplifier

                  That should be correct, even the pdf has a .1uf on the output https://cdn.badcaps-static.com/pdfs/...edee6b237e.pdf

                    Comment

                    • linksys1127
                      Senior Member
                      • Sep 2016
                      • 121
                      • United States
                      #6
                      Re: Elan z660/661 amplifier

                      Ok thank you for your help

                        Comment

                        Previous template Next

                        Related Topics

                        Collapse
                        • MrCommunistGen
                          Polk Audio RTi100 Plate Amplifier won't power on and intermittently honks and buzzes
                          by MrCommunistGen
                          My childhood best friend was killed about 9 years ago. His parents are finally letting go of his things, and they offered me his Polk RTi100 tower speakers. The Polk RTi100 towers are one of a handful of designs from the early 2000s that is a full range 3-way tower with a built-in self-powered subwoofer. This is accomplished with a plate amp integrated into the speaker input panel.

                          I think they used them for a while, but they've been sitting for at least a few years now. After about 40 hours of driving to their house and back (both they and I have moved in the last 9 years) I got...
                          07-12-2021, 05:11 PM
                        • jinu_j
                          How to test Subwoofer Amplifier with only a multimeter
                          by jinu_j
                          Hi Folks

                          Need some advice on how to test a subwoofer amplifier if i have access to only a multimeter.

                          Problem
                          I have a Boston Acoustics active Subwoofer (soundware S). Its rated output is 200W. But the output i am getting is very low i can barely hear/feel it even if put the gain at max. I replaced all the capacitors in the Subwoofer amplifier but still no change.

                          Is there anyway to test this without getting an oscilloscope/Function generator to see if the fault is with amplifier, driver or the source??

                          Any advice would be appreciated...
                          08-29-2024, 02:05 AM
                        • UserXP
                          Mackie CR4 amplifier no sound
                          by UserXP
                          Hi, people.

                          I've got an amplifier assembly from Mackie CR4 parts. It's just an amplifier, there was no speaker housing, so I used my set of CR4s to test it.

                          Anyway, upon connecting everything and hooking the "new" amplifier to an audio source, the sound played clearly and strongly for the first ten seconds. I was happy it was working. Then the sound started to fade out during the playback until it was no more. After it had "dropped to zero", there were two very short intervals of sound playing at the normal volume, as if the amplifier was trying to...
                          10-17-2020, 05:06 PM
                        • Coert van Dorsten
                          Sansui Integrated Amplifier replacement volume control troubles
                          by Coert van Dorsten
                          Hi all you clever electronmic gooroos!

                          I was wondering if you could help me with the below issues Im having on a Sansui Integrated amplifier. I bought this unit as a project to repair as Im playing around with basic electromics.The unit has a faulty volume control pot. The service maual refers to a 150K Logarithmic pot (A) tapered stereo. Im struggling to find this value. Seem to be a jump from 100K to 250K. Im now trying a 250K pot. It works but the problem is that as the volume is turned up from starting at Min the Left channel will come on first just slightly before the Right...
                          10-15-2025, 02:54 PM
                        • mikey5791
                          Help on car amplifier only one channel works
                          by mikey5791
                          Hi all forum members,
                          Fyi, i have been working on this old model PCT-4082 (4 channel car amplifier). The owner said only one channel is working.
                          My initial finding is this amp originally use Toshiba 2SA1943 and 2SC5200 transistor for its output but after opening the top casing i found it used Toshiba A1941 (pnp)and C5198(npn). I desoldered all the 4 pairs transistors and found 1 piece A1941 open(tested "OL" on all legs) and replaced the 1st pair with 2SA1943 and 2SC5200, thats why you can see in the picture it is the bigger size transistor. The other A1941 and C5198 all...
                          08-06-2025, 10:36 PM
                        • Loading...
                        • No more items.
                        Working...