Alpine mrx-v60 no sound output

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • audiofreak19
    Badcaps Veteran
    • Apr 2013
    • 556
    • usa

    #1

    Alpine mrx-v60 no sound output

    I just picked this amp up that powers on but no sound output. I'm not sure where to start besides the caps are fine on it.
  • xxxvirus1987xxx
    unlegendary
    • Sep 2014
    • 24
    • philippines

    #2
    Re: Alpine mrx-v60 no sound output

    check firts vcc or the rail voltage are the voltage are present..
    check power tranny or powe transistor...
    check resistors diode etc..

    Comment

    Related Topics

    Collapse

    • FrancescoV
      Onkyo HT-R390 no sound output, video output ok
      by FrancescoV
      Good morning everyone,
      I'm trying to repair an onkyo ht-r390 that has no sound output, despite the volume being at maximum, the rest seems to work; the video output signal (coming from an hdmi input) is present, but the audio is absent. Similar situation if I send an audio signal from any input I have no output.

      The firmware reported is the following:
      M:1.00/11107BLP
      D:?.??/????????
      O:1.00/11107AL

      The DSP firmware given the question marks seems corrupt.

      On the BCHDM-0678 - 25140678 - QPWBCHDM0678A0 board the chip that usually seems...
      05-11-2025, 02:59 AM
    • Jedi134
      Uniden bearcat UBC 360clt no sound output
      by Jedi134
      Hi I have inherited the above desktop scanner, all seems to work correctly but there is no sound output. The only sound I do get from the speaker is the beep confirmation when you press a key. No output from the headphone socket either. Not even radio static with squelch fully turned down, tried a reset by holding 2, 9, and hold buttons but still no sound, does anyone have any experience with these scanners, thanks.
      05-13-2024, 04:12 AM
    • Rupsenkind
      Yamaha RX-A1030 working, no sound output
      by Rupsenkind
      Hi all, I've started this new thread in order to avoid further polution of thread "Yamaha RX-A3010 working, no sound output"
      Just to recap:

      No sound through Audio and AV analogue inputs, only sound when 2ch stereo or pure direct is activated (so no sound when I e.g. choose 7ch of Hall in Munich etc.). Hoever when I connect HDMI I've sound in all options (movie, music, eyc.) First suspicion was the DSP chip/PCB so I bought a scrap 1030 with a good functioning PCB (in this one a driver stage was defective (PRT DC: 67), after I swapped the PCB I've performed a factory...
      07-10-2022, 03:15 AM
    • r2digital
      Boston Acoustic MSUB no sound output(pics)
      by r2digital
      The off/on/auto switch was busted so i forced it into auto mode and now the blue light comes on but i don’t get any audio output. Does anyone one have any experience repairing this amplifier? I looked it over, checked some the of output transistors, some of the power resistors and cleaned that nasty conductive epoxy glue stuff off but not having much luck in the trouble shooting department.

      I did however find a part of the PCB that was discolored from heat...
      03-22-2024, 06:00 PM
    • proxneo
      Bose Wave I AWRCC1 - intermittent to no sound output - loud popping & crackle sounds
      by proxneo
      Dear reader

      I have been asked to check out a faulty Bose Wave system belonging to a relative. The faulty unit produces loud intermittent pops and crackles. Sometimes there is speaker audio output (FM/AM, CD etc.), most of the time there isn't. This behaviour degraded over time fairly quickly, to the current situation where no sound is put out at all. Gently messing and wiggling wires, connectors or heatsink has no effect in force-replicating the problem. I have little experience in audio repair when it comes to (main)board electronic component faults. Bose repair WAS about 140$ (most...
      12-02-2023, 09:27 AM
    • Loading...
    • No more items.
    Working...