Yamaha EMX 512SC - Bad Limiter?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • honeybadger0
    New Member
    • Nov 2024
    • 2
    • United States
    #1

    Yamaha EMX 512SC - Bad Limiter?

    I have a Yamaha EMX 512sc powered mixer that gets heavy use. Recently a new problem has arisen ... it seems like the L output is way more sensitive than the R and the limiter light for main L is flashing even at very low (below the 2 setting on the knob) levels.

    It seems to be across all channels and with different inputs. The speakers have been recently tested as well and do not seem to have any of their own issues.

    Has anyone else encountered this problem and could help me out?​
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • Phlox321
      Yamaha EMX 2000 Powered Mixer issue
      by Phlox321
      Hi All

      I have a yamaha emx 2000 powered mixer im trying to repeair.
      the problem is that theres no sound output on the right channel. Left channel works fine.
      Right channel has output when using the phono(headphone output) but not when going through the amplifier
      the left peak meters work but not the right
      the clipping light however does come on when gain is turned up same as left channel
      What i have done so far is make sure that the supply voltages are fine, which they are
      I found several cracked solder joints on the amplifier board which...
      10-19-2022, 11:45 AM
    • Bektronics
      Schematic Digital Audio mixer RCF type M18
      by Bektronics
      Hello dear audio friends.

      I am feverishly looking for the full electronic schematic (not a block diagram) of the RCF type M18 digital audio mixer.
      The device does not make a WIFI connection with my Apple tablet and yet I have already installed the recent app on it.
      I suspect that there is a problem in the mixer itself with the WIFI card and of course I would like to see this on an extensive schedule before opening the device.
      Thanks in advance if anyone can help me with this schematic.
      Of course, all information about this digital mixer and possibly references...
      07-24-2023, 06:40 AM
    • sanalelevenstar
      Yamaha RX-V485 Wn9711 Update
      by sanalelevenstar
      Help Needed: Yamaha RX-V485 Network Issue After Firmware Update (WN9711 Error)

      Hi everyone,

      I'm facing an issue with my Yamaha RX-V485 receiver. During a firmware update, the process failed, and now the USB, Bluetooth, and network functionalities are not working. Occasionally, the receiver displays the error code WN9711.

      I came across Yamaha Technical Bulletin No. 0103, which describes a similar issue for models like the RX-V4A, RX-V6A, and RX-A2A. According to the bulletin, the issue can be resolved by shorting soldering points (e.g., J260 for RX-V4A or...
      12-04-2024, 04:32 AM
    • Thermaltake
      Power button on Behringer Xenyx 1204USB mixer dead ?
      by Thermaltake
      Hi, I got Behringer Xenyx 1204USB mixer, and in the morning mixer was working fine, but when I came home from bike ride I turn it On but nothing happend. Phantom switch is working because red light is On, but other switch no respond.
      I brought mixer to my friend today who is electronic expert and he will tell me if it's the button or something on power supply that died. But I am 90% sure that it's power button. My question is, is it possible to put some better quality switches on that mixer than the ones mixer came with, I found them very cheap and low quality.
      08-16-2022, 03:22 AM
    • jjne
      Yamaha RX V675 sound issues
      by jjne
      I have an old Yamaha RX V675 receiver which is starting to develop issues with the sound, although it doesn't quite match up with what folk normally report with these.

      From cold, the sound cuts in and out. When this happens the amp is losing sync with the optical input (speaker graphic disappears from the front panel). But this is not resolved by putting the unit into pure direct mode. After a couple of minutes this resolves, although there are occasional clicks from the speakers after that.

      At first I thought it was either a speaker relay or the DSP, but I don't think...
      06-24-2025, 07:01 AM
    • Loading...
    • No more items.
    Working...