[ROM] Abir X6 vacuum robot

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • lietuvis10
    Member
    • Aug 2019
    • 18
    • Lithuania
    #1

    [ROM] Abir X6 vacuum robot

    Hello, I would like to share Abir x6 vacuum robot cleaner rom files that I extracted from SPI ROM chips. One chip is on main board and another is on camera module (the problem with robot was in camera rom, after re-write with other robot's rom it started working perfectly fine).

    Maybe this will help you, because I couldn't find it anywhere.

    Camera Dump: 4MB
    MB Dump: 2MB
    Attached Files
    Tags: None
    • ljgonzalo
      New Member
      • Jul 2022
      • 1
      • Argentina
      #2
      Re: [ROM] Abir X6 vacuum robot

      Hi lietuvis, what was your problem with de Vacuum robot?

        Comment

        Previous template Next

        Related Topics

        Collapse
        • ex250
          SDJ01RM vacuum robot not powers on, all dead
          by ex250
          Hi friends, I have this vacuum robot at home that is not starting any more, no leds working, power button doing nothing, battery reading seems ok arround 14.4v, I suspect that mainboard is faulty, seems that there is not any clear brand model on it, and of course could not find any schematic. The trand of the vacuum is the Roidmi SDJ01RM, on some sites appears as vacuum mop Eve plus 60 or similar

          If any one could point for where to start... would appreciate, new board is quite expensive arround 100 USD or more

          Many thanks and Merry Christmas to all...
          12-24-2022, 05:12 AM
        • Ahari
          Request HP Proliant Microserver Gen 8 (J06) BIOS dump to restore system firmware
          by Ahari
          Hi all,

          This is my first post here (I am very new to forums!) and I hope someone can help. I am looking for a full dump of the BIOS of a HP Proliant Microserver Gen 8 so that I can get this mini server running again. (BIOS version J06 2019-04-04, chip 25Q064A). I think my board was partially bricked after a failed BIOS update.

          I got it second hand in this state and all the normal attempts at bios restoration have not worked. I have even desoldered the chip and tried to load the actual BIOS from HP, but it is missing some parts needed to boot the system.

          I...
          08-13-2025, 06:12 AM
        • flat-earther
          Hoover FM216LI cordless vacuum refuses to charge
          by flat-earther
          I have a Hoover FM216LI cordless vacuum which isn't charging its internal battery.

          I opened up the unit, and it has 6x Samsung ICR18650-22P cells connected in series.
          5 cells were at about 3.3-3.1V. one was at 2.4V, so I assumed this cell was bad that's why the vacuum wasn't charging so I replaced it with another 18650, but after that the problem still persists, the vacuum turns on a bit and then cuts out since the batteries are empty.

          So I think the over discharged battery wasn't the culprit, it was a symptom of the unit not being able to charge its batteries....
          06-06-2025, 03:14 AM
        • Awesomerp
          Sencor SVC7020BK robot vacuum cleaner problem
          by Awesomerp
          Hello I have been trying to identify and fix a problem with a robot vacuum cleaner, which when switched on cleans for like 3-4 seconds and stops, all the driving, sweeping and vaccum motors stop.
          On the pcb from a battery connector up to a main microcontroller everything seems to be fine (vcc pin input is 5v constant when a switch is switched on).
          And the switch itself is fine looking at the quality of my soldering
          Red LED keeps blinking during those 3-4 working seconds, and when the robot stops LED just remains lit.
          The green one for some reason does not even...
          09-23-2022, 11:36 AM
        • mkdj
          ASUS ZenBook UX480F : need help with cleaning the ME region of my BIOS dump
          by mkdj
          Dear all,
          I have a ASUS ZenBook UX480F with the following symptoms:



          I suspect it is a BIOS issue. So I decided to try to clean the ME region. I followed the guide on win-raid, and I believe I have done everything correctly. My problem is: when I open the outimage.bin in ME Analyzer, it says that it is Extracted, and not Region, Extracted as it should be. Is it normal, or did I do something not correctly? This is my first experience editing BIOS files.

          I would appreciate if someone could take time to explain the issue, so that I can learn. But I would...
          10-19-2025, 04:41 AM
        • Loading...
        • No more items.
        Working...