LG Air Conditioner AC unit bypass

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • domix
    Senior Member
    • Jan 2014
    • 171
    • Slovenia
    #1

    LG Air Conditioner AC unit bypass

    Hello,
    i have Lg AC indoor unit connected to heatpump warm water. To flow thru unit. I have it to heating up garage. I have previus old indoor ac unit. It was only connected to power supply and is was woking.

    Now i have new one which has a problem, it needs outdoor unit. It has error, 5 blinks which means that outdoor unit is not connected.

    how can i bypass this :/

    I need only to turn on and i need only fan to blow, and adjust speed od fan. To blow over a warm pipes.
    2 Photos
    Tags: None
    • lotas
      Badcaps Legend
      • Jan 2016
      • 4905
      • Russia
      #2
      This indoor unit won't work without the original outdoor unit, and you can't fool it, since it has a CPU built into the firmware, and the outdoor unit also has a board with a CPU. They communicate between the units via two wires, 2 "N" and 3 "C." When turned on, a self-test is performed, and if the indoor unit doesn't detect the outdoor unit, it displays an error and the unit is blocked.
      The old indoor unit does not need an outdoor unit, since they do not exchange data; the compressor, fan, and four-way valve are simply switched on via a relay to switch the heat.

      Last edited by lotas; Yesterday, 04:28 PM.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • salah11
          No Ringer Sound in Intercom outdoor panel (Voice Communication Works)
          by salah11
          Hello everyone,
          I have a persistent issue with a commercial intercom system (likely made in Turkey, based on the unit). Voice communication (audio) works perfectly, but the outdoor panel did not return the ring when the call button is pressed.
          Whell the system consists of three main circuit boards (see attached photos):
          A. Board 1: Power Supply / Ringer Generator (White Board) with LS1240A, BD442 and BD140 Power transistors for ring amplification.
          B. Board 2: Handset (Indoor Unit) Role: Contains the microphone, the speaker/baffle, the manual hook switch, and the open-door...
          11-21-2025, 01:08 PM
        • ngml
          Repair of an LG split AC system indoor unit PCB
          by ngml
          I am trying to repair an LG split AC indoor unit, which does not start and gives a CH05 error code.
          This indicates an error in the communication between the outdoor and the indoor unit.
          The outdoor unit is fine, so the problem is the indoor PCB.
          The indoor unit is an LG PC09SQ NSJ (3SNM09JA2FA), and the PCB has the following type number: EAX35907219-1.2 (see photo1)
          I changed optocouplers ICO1X & ICO2X and the NPN transistor S9013 which drives optocoupler ICO2X (see photo2), but this did not remedy the fault.

          Does anybody have the schematics of this board,...
          2 Photos
          02-01-2025, 12:55 PM
        • Gjackson
          Air-conditioning unit power supply failing to power up
          by Gjackson
          Hi all, I managed to narrow down which PCB was causing my Haier AC to throw out an E7 error code (E7 indicates that the indoor unit and outdoor unit cannot communicate). I found that the outdoor unit power board which gives 5v and 15v to the outdoor unit module board fails to fully power up.. The power Led starts to fade in incredibly slowly and the 5v and 15v power buses jump around like crazy and never reach their required voltage. I unplugged the module board from the power board and the power board powered up fine! It had a steady 5v and 15v out and the power LED came on instantly and Bright....
          01-08-2022, 09:24 AM
        • carrzkiss
          Cyberpower cps1500avr not charging batteries
          by carrzkiss
          Hello, all.

          Cyberpower Battery Backup Unit.

          I bought two new ML18-12 batteries through Amazon (They have already refunded my money for the two batteries as we thought the batteries might have been bad.)
          When I got them in, they were not fully charged. I connected them to the UPS and waited 24 hours before connecting any networking equipment.
          In parallel, they read 24v, but within 24 hours, the meter on the front of the unit dropped from 4 to 3 bars on the battery charge indicator.
          Checking the voltage, it was down to 22v.
          I quickly removed everything...
          06-15-2024, 02:10 PM
        • Gjackson
          Understanding air conditioner PSU logic
          by Gjackson
          Hi all,

          I have an air conditioner outdoor control board that I'm trying to understand how it functions. In short, the board takes in 240VAC and splits it into 4 other wires, 2 of these go to power the indoor unit and another 2 go to power the outdoor unit module board. the 310VDC capacitor bank on the outdoor control board get charged up from a rectifier on the outdoor module board. Now what I can't wrap my mind around is the fact that there is a relay in between the 2 mains wires that go from the outdoor control board to the outdoor module board which is normally open, what this...
          11-25-2022, 10:45 AM
        • Loading...
        • No more items.
        Working...