I taped al 10 CLK pins, image is like as it should be. Every thing works
should inleave it so? Or i will need to find if only one or two pins is making problems? It will be okey if i leave it masked all 10 clk pins?
domix
Senior Member
Last Activity: Today, 01:20 PM
Joined: 01-14-2014
Location: Mb
-
Yes i search at net for bloking signals with tape ot paper, but didnt find this model.
which pins should i to mask on ribbons cable?Leave a comment:
-
I get new t-con board. I replace it, and when turn the tv on it turn on only backlight whitout 5 times blinking red.
so the problem is almost the same just like wiht orginal t-con board.
i didnt get any android sound. If i disconnect u cable from t-con to buffer board. I only get half of screen white color and nothing other on screen.
any other solution to check?
thanksLeave a comment:
-
Anyone?Leave a comment:
-
Should i replace which board?Leave a comment:
-
No i dont have sound and no image. I have backlight and 1/2 screen is withe, i i sepparater UCable modules i have only 1/4 screen withe color and 3/4 screen is only backlight. Where is supposed to be image is only bright withe.Leave a comment:
-
I have dissconnected it in the middle. I have second 1/4 of screen withe. Here are photos.
​Leave a comment:
-
Here is the photo. i take the tv it from the wall.
when i unplug right flat cable (mark it on the image) from T-con i get half screen white. When plug it back and unplug left one. I get 5 blinking red.Leave a comment:
-
Sony KD - 75XF8596
Hello,
i have this tv. Now i dont have image only backlight.
when i turn it on backlight turn on and white led. After a few secodns i get red led blinking 5 times.
is any common issue, for sony bravia. Panel, board? Before i unmount it from the wall and open it up.
thanks -
I heat it wit hot air gun pn 150C at the back side of the main chip, than carefuly put it in oven preheated on 180C for 40 seconds. Now work just perfect, everything is fineLeave a comment:
-
I dont have option for reballing, i can reflow with hotair or i put it in oven :PLeave a comment:
-
47pfl6008 blinking red
Hello,
i have 47pfl6008, at latest half a year sometimes TV turns OFF suddenly. Then you need to turn ON again. Yesterday when i want to turn it ON, red light blink two times than pause, and again two times in a sequence. I plug it out and then back in. Now the red light is off and TV wont turn on, only a short red blink for 0,1sec.
What to check, seems everything oken on MB.... -
Re: Bosch GSB 12V-15 water damage
Switch is clean. Got voltage on output. Maybe is circuti? Start to search for new one?Leave a comment:
-
Re: Bosch GSB 12V-15 water damage
I cleaned motor now, work well direct to battery. But if i connect thru circut nothing happend, only LED
Should i open a switch and clean it? But if led turn on than i think it worksLast edited by domix; 09-01-2023, 08:09 AM.Leave a comment:
-
Re: Bosch GSB 12V-15 water damage
Motor works, but only direct on bypass battery-motor. Over circuit and switch turn on only led light, motor doesn't startLeave a comment:
-
Bosch GSB 12V-15 water damage
Hello,
My tool was spashed with water. It was wet, i dry tool and when i push a switch only lights turn on. Motor is not working.
I washed the board inside with contact spray. I can turn motor by hand i clean contacts.
If i connect battery direct on motor + + and - - it turns very slowy and cables are hot in two seconds.
What else could be.
Thanks... -
42PFL3606H/58 no power
Hello,
At this tv i have no power. I open it up. Fuse was blown and this on picture 2 is blown at one leg.
What to? New chip and fuse or new board?
What can i check.
Thanks... -
Re: Caterpillar T20 - wont turn on
I'm from Europe - Slovenia
...
Leave a comment:
-
Re: Caterpillar T20 - wont turn on
I unplug the battery and want to turn on, obviously wont operate without battery.
I check on net for new battery, i dont find any of the website to buy new one ��Leave a comment:
-
Caterpillar T20 - wont turn on
Hello,
my CAT t20 tablet wont turn on. It was in drawer for half a year.
Now cant turn it on. Charger have 5,3V. It was plugged in for 24h and nothing.
I open it and meassure there like on attached pics. If i unplugg the battery and connect charger nothing.
What to look
Thanks...
No activity results to display
Leave a comment: