tx2-8fz relay substitute

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • petehall347
    Badcaps Legend
    • Jan 2015
    • 4422
    • United Kingdom

    #1

    tx2-8fz relay substitute

    i am trying to find a relay to substitute tx2-8fz as a drop in replacement because i cant find it in the uk and its for a rush job . i have room for 2 separate relays but cant find with same specs . i don't know the capability of whatever drives the coils as most of the board is still buried in rubber stuff so want to keep close to original .
    data sheet here .. https://www.alldatasheet.com/datashe...1/TX2-8FZ.html
  • sam_sam_sam
    Badcaps Legend
    • Jul 2011
    • 6018
    • USA

    #2
    Re: tx2-8fz relay substitute

    You just need to find a single coil at roughly 200 ohms pull in voltage at roughly at 6 volts
    drop out voltage for there specifications are bogus 0.7 volts the lower the voltage the better but do not be to worried about this specific value to much

    I would just find a automotive type relay that is very similar in specifications and try it unless this relay is connected to a computer on this device then you have to have the specifications as close as possible to not have a conflict with the computer

    I found something but the specifications are not the same for the coil voltage pull in voltage and the resistance is not the same but it might work if it is not controlled by a computer or some type of micro controller if it has some type of current sensor device hooked to coil

    https://cdn.badcaps-static.com/pdfs/...b179a1869e.pdf

    Or

    https://cdn.badcaps-static.com/pdfs/...d9faf4d816.pdf

    Please post a picture of the board if you can or what is controlling

    The question I have is this a latching type relay or is it a bidirectional type of relay it does make a difference to use the right type of relay

    Do you know what the difference is between the two types of relays if you do not I can explain the difference between the two different types

    Because I have used both types of relays before

    You can use a normal type of relay for either type of relay mentioned earlier however the results of operation will be some what different for the latching relay type

    A seller on AliExpress has them in stock unfortunately I can not post the link to it
    A seller on EBay has used ones for sale however it is EBay USA website

    I hope this helps you
    Last edited by sam_sam_sam; 07-23-2021, 05:46 AM.

    Comment

    • petehall347
      Badcaps Legend
      • Jan 2015
      • 4422
      • United Kingdom

      #3
      Re: tx2-8fz relay substitute

      its a dual relay .or rather 2 relays in the same box . looks like we will have to wait for the right one to come from china . i have cleaned the contacts for now so the customer can use the machine for now and bring it back in for new relay fitted .
      its basically same as this but this mower is diesel so has stop solenoid to relay . https://www.orangetractortalks.com/f...o-start.13761/

      Comment

      • sam_sam_sam
        Badcaps Legend
        • Jul 2011
        • 6018
        • USA

        #4
        Re: tx2-8fz relay substitute

        Okay thanks for letting me know what it is used for

        Comment

        Related Topics

        Collapse

        • edugimeno
          Find substitute for mosfet in servo board of versacamm sp-540v plotter
          by edugimeno
          Hi There!
          I am currently serviciing a plotter versacamm sp-540v
          I found a shorted mosfet labeled J553 which corresponds with SJ-553s (surface mount)
          Neither local stores nor other webpages that are able to provide it before 1 month (only aliexpress, with 1 month delivery) can provide this part
          I need to find a substitute for it. Can anyone give me a hint on a part that I can use to replace it?

          Also, given the schematic Im attaching (pg 36, transsitor Q1) , does it make sense that the whole machine won't turn on when I press the POWER button on the panel? This...
          10-27-2022, 10:46 AM
        • valvashon
          Repair Success! Middle Atlantic UPS2200R-IP
          by valvashon
          Yesterday I successfully repaired a Middle Atlantic UPS2200R-IP that had inadvertently been used as a surge suppressor at our transmitter site. It has already been replaced with an updated one but it's coming home with me now instead of being e-cycled. To be specific, this is the MA model that has the blue backlit display and has been discontinued, although this design may have been used in many UPS units including the smaller Middle Atlantic ones in this series.



          Here's what happened: We experienced a brownout/surge at the site, which damaged the UPS and took our broadcasting...
          02-06-2024, 12:54 PM
        • Vesko356
          [Guide] How to find the right HP bios version to flash
          by Vesko356
          First of all thanks to all of our members who have posted previously all methods posted here.
          Please leave a comment if you find something new,or have anything else to add.
          -----------------------------------------------------------------------------------------

          Find by serial number,model number or series

          If you know the laptop serial or model number go to HP support https://support.hp.com/us-en/drivers/laptops .
          Enter the serial number or model number and click submit.On the next screen you will have to enter the OS
          Operating system and OS version.If...
          08-11-2023, 03:27 AM
        • sam_sam_sam
          Mitsubishi CNC switching power supply board dead / relay board bad diode failure
          by sam_sam_sam
          I was working on this CNC machine today found no keyboard functioning no control relay powering on
          The screen powered on and was giving an operation error but the manual was not very clear about what the error exactly was but with a little bit of troubleshooting and finding out that the control relays not powering on and no keyboard functions we narrowed down to this one switching power supply which of course does not have any indicator LED light they are on the keyboard interface/relay controller board

          Found shorted diodes on main controller relays there are 3 of them that...
          01-07-2023, 05:43 PM
        • flibidy
          Magnum IA.100 Amplifier Switches on, No Output, Possible Input Side fault?
          by flibidy
          I have here a Magnum IA.100 which belongs to my parents.



          The unit powers on & when the relay kicks in, you get a pop from the speakers (this might sound weird but is usual behavior for this amp). However, you get nothing coming through it from any of the inputs & no pops and crackls from any of the controls.


          Because of the sound from the speaker when the amp turns on I have assumed that the output section probably works but I could be wrong & I'm not sure how to test that side of things further.


          What Ive done........
          01-01-2025, 01:26 PM
        • Loading...
        • No more items.
        Working...