RF connector repair

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • capwizard
    Badcaps Legend
    • Jun 2016
    • 1991
    • USA
    #1

    RF connector repair

    For RF connector repair I am the Best in town..............

    PS: used solder wick circuits as a reinforcement. A piece of RF cable uses as a heat sink to dispatch the heat.
    Attached Files
    Last edited by capwizard; 03-06-2017, 12:05 PM.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • Tomylee
      No LCD image after connector replacement – lifted components and damaged resistor (Nintendo Switch Lite HDH-CPU-02)
      by Tomylee
      Hi everyone,

      Sorry for the person who’s going to read all this !
      I'm on a Nintendo Switch Lite, motherboard HDH-CPU-02.

      While replacing the left joystick, I had to remove the motherboard to access the connector underneath. When I lifted the LCD connector latch, it broke (the plastic had become brittle over time), so I replaced the entire connector.

      During the desoldering of the LCD connector using hot air, three small components located just below the connector (likely 0402 capacitors) came off and remained stuck to the bottom of the...
      07-11-2025, 11:52 AM
    • 5mall5nail5
      Help identifying connector for ASUS 4090 Strix RGB LED connector
      by 5mall5nail5
      Hi All -

      I had replaced my ASUS 4090 Strix cooler with a waterblock and put the stock cooler on the shelf. Was moving it and snagged my sweater on the connector and pulled the wires out of the pins on the RGB connector. I tried to get them back on but its too small so I opened the stamped pins and tried to solder but its not a good repair and the wire broke on reinstallation.

      Looking to replace the connector on the cable side and get pins to crimp onto a new cable. Bought random JST and such but nothing is correct. Can anyone help identify the connector and possibly matching...
      05-04-2025, 07:47 AM
    • howardc64
      A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
      by howardc64
      Problem

      This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
      08-04-2024, 10:36 PM
    • bussincaps
      MacBook Pro Mid-2014 A1398 Retina LED Controller Connector [First Repair (Disaster)]
      by bussincaps
      Hello All,

      tl;dr: minimal electronics experience and my first repair, lifted 8 pads off the laptop display LED controller board when attempting a connector replacement, options are attempting pad repair or jump wiring.

      Laptop Model: MacBook Pro 15 Mid-2014 Retina, A1398 MGXA2LL/A
      eDP Display: Samsung LSN154YL01-A02, assembly sold as Apple part 661-8310
      Soldering Equipment: Hakko FX-888D w/ T-18 tips (Chisel, Conical, Bevel types)

      I needed to replace the 30-pin I-PEX Cabline connector (labeled J8300 in the Apple 820-3662 mainboard schematics),...
      08-03-2023, 12:57 PM
    • michhak
      Toshiba Satellite M50-A keyboard connector on LA-A481P motherboard
      by michhak
      Hi guys,
      i have a damaged keyboard connector on my older Toshiba Satellite M50-A laptop. I know there is LA-A481P motherboard. In attachment pictures there is a real looking connector and i also found a schematic to the connector. But i need help with finding a real electronic part to replace the damaged connector. e.g. on aliexpress (or different page).
      It is 34pin connector and the length from pin n.1 to pin n.34 is 26mm. So it means a pitch length is 0.764 mm. I have seen connectors with 0.5mm , 0.7mm , 0.8mm and 1mm pitch length. But not with 0.75. Is it some special custom connector...
      11-17-2021, 05:45 AM
    • Loading...
    • No more items.
    Working...