Faulty IDE to USB adaptor (drive makes funny noise, doesn't detect)

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • Agent24
    I see dead caps
    • Oct 2007
    • 4939
    • New Zealand
    #21
    Re: Faulty IDE to USB adaptor (drive makes funny noise, doesn't detect)

    USB cable shouldn't be too hard, even though it is A -> A rather than A -> B...

    But the IDE cable could be interesting... the header thing is actually soldered to the board directly somehow.

    Any ideas for removal if I need to?
    "Tantalum for the brave, Solid Aluminium for the wise, Wet Electrolytic for the adventurous"
    -David VanHorn

      Comment

      • Badcappy
        Banned
        • Aug 2007
        • 52
        #22
        Re: Faulty IDE to USB adaptor (drive makes funny noise, doesn't detect)

        USB (especially 2.0 High Speed mode) is very sensitive to EMI, try some grounded shielding.

          Comment

          Previous 1 2 template Next

          Related Topics

          Collapse
          • Document Archive
            HP EliteBook 850 G5 + Mini Dock, Bag & Spare AC Adaptor Notebook 800 Specification for Upgrade or Repair
            by Document Archive
            This specification for the HP EliteBook 850 G5 + Mini Dock, Bag & Spare AC Adaptor Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the 850 G5 + Mini Dock, Bag & Spare AC Adaptor boardview and 850 G5 + Mini Dock, Bag & Spare AC Adaptor schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant...
            09-06-2024, 08:50 AM
          • tony359
            Removing electrical noise introduced by fan
            by tony359
            Hi all,

            I am working on a sound processor, it tends to overheat so I fitted a fan inside. The fan is connected to the +15V of the PSU via a DC-DC converter based on the LM2596 to reduce the voltage to around 10.5V.

            Unfortunately the analogue circuitry is picking up the noise from the fan in two ways:
            1. The fan is close to the analogue section, the motor itself gets into the outputs so I'll have to move it somewhere else
            2. Even with the fan running outside of the case, there is still some noise which is clearly going back to the processor via power line....
            2 Photos
            11-28-2023, 05:18 AM
          • MegaZAC
            Onkyo TX-SR805 noise in one channel
            by MegaZAC
            Surprisingly enough, this receiver doesn't have the DSP chip issue. The HDMI board does not get hot, and sound over HDMI works fine.

            Regardless of the input, the right channel has noise that is clearly noticeable even on average volume level. The only cases when there's no noise is when VCR input is selected (some tracks on the board are damaged, maybe that's why), or if HDMI input is selected but nothing plugged into it. In all other cases, even when no input is connected I still have the noise.

            There's some logic behind it. As soon as I select an input I get only left...
            04-23-2025, 10:09 PM
          • courtcircuit
            Philips HTS8000 home cinema noise problem
            by courtcircuit
            Hello

            I have since a long time a Philips HTS8010S/01 which has been old but was doing the job.

            Since a few days, it starts by making a weird "static" nois when switches on for a few seconds to a minute and then works like a charm.
            Noise loudly outputs from the 3 channels, even if no signal is sent by the controler.DVD to the subwoofer/amp unit.

            I was thinking of a soldering that was starting to be damaged and that was only doing the job after a few seconds of heating, most probbaly on the power board
            Removed each of tyhe boards
            ...
            02-08-2025, 08:22 AM
          • karatzdi
            Denon AVR 1908, High pitch noise on Surround back Left channel after long overhaul
            by karatzdi
            Hello,

            I know some might say... just buy another one. Sell it as parts..!

            So had this AMP for quite some time. Recently I saw light smoke coming out of the AMP. Had my fire extinguisher close by. Just kidding. Turned immediately all devices off from mains.
            Let things cool a bit, and opened up the amp device. I clearly saw on the main board which hosts the 5X amp (5.1), 3 10 ohms 1W resistors had their leads looking black, while the rest of the remaining 2 x 10 ohms were brownish as being installed from factory.

            Spent some time downloading the Service...
            06-11-2024, 08:38 AM
          • Loading...
          • No more items.
          Working...